HFBR-1505CFZ Datasheet HFBR-1515BFZ, HFBR-2515BFZ, HFBR-2505AFZ | P1-P3

is a registered trademark of AT&T.

HCS

is a registered trademark of OFS Corporation.

HFBR-1505AFZ/2505AFZ (SMA Tx/Rx for SERCOS)

HFBR-1515BFZ/2515BFZ (ST

Tx/Rx for PROFIBUS)

HFBR-1505CFZ/2505CFZ (SMA Tx/Rx for INTERBUS-S)

Full Metal Fiber Optic Transmitters and Receivers

for SERCOS, PROFIBUS and INTERBUS-S Applications

Data Sheet

Features

 Meets industrial SERCOS, PROFIBUS, and INTERBUS-S

standard

 SMA and ST

ports

 650 nm wavelength technology

 Metal housing and port

 Speci ed for use with 1 mm plastic optical  ber and

200 μm hard clad silica

 Auto-insertable and wave solderable

 DC – 10 MBd data rate

 RoHS-compliant

Applications

 Industrial control data links

 Factory automation data links

 Voltage isolation applications

 PLCs

 Motor drives

 Sensor, meter and actuator interfaces

Description

SERCOS

SERCOS, an acronym for SErial Realtime COmmunications

System, is a standard digital interface for communication

in industrial CNC applications. SERCOS is a European

(EN 61491) and international standard (IEC 61491). The

optical interface allows data rates of 2, 4, 8, and 16

MBd and data transfer between numerical controls and

drives via  ber-optic rings, with voltage isolation and

noise immunity. The HFBR-1505AFZ and HFBR-2505AFZ

products comply with SERCOS speci cations for optical

characteristics and connector style, and have guaranteed

performance up to 10 MBd. (16MBd SERCOS device is also

available, please contact Avago for more information.)

PROFIBUS

PROFIBUS, an acronym of PROcess FIeld BUS, is an open

 eldbus standard de ned for data rates ranging from 9.6

kBd to 12 MBd in selectable steps for wire and optical

 ber. PROFIBUS is a German national DIN 19245 stan-

dard and a European CENELEC standard EN 50170. The

connector is the recommended optical port of the

PROFIBUS optical  ber version but other connectors are

allowed as well. The HFBR-1515BFZ and HFBR-2515BFZ

comply fully to the technical guideline using Plastic

Optical Fiber up to 6 MBd, and have a guaranteed per-

formance at data rates up to 10 MBd.

INTERBUS-S

INTERBUS-S, a special open Sensor/Actuator Bus, is

 nding a broad acceptance in the factory automation

industry. The HFBR-1505CFZ and HFBR-2505CFZ were

specially designed for this application and can be used

with 1 mm POF and 200 μm HCS  ber at the speci ed

data rates of 500 kBd and 2 MBd. The optical transmis-

sion guideline is a supplement of the German National

DIN E 19258 standard draft. On the European level, prEN

50254 is the draft of the INTERBUS-S  eldbus.

Speci cations and content subject to change without prior noti cation.

Speci ed Link Performance

-40˚C to +85°C unless otherwise noted.

Parameter Symbol Min. Max. Unit Condition Reference

Link Distance with 1 0.1 40 m POF Notes 1, 2, 3, 4, 6

HFBR-1505AFZ/2505AFZ or 0.1 100 m HCS

Notes 1, 2, 3, 5, 6

HFBR-1515BFZ/2515BFZ

Link Distance with 1 0.1 50 m POF Notes 1, 2, 3, 4, 7

HFBR-1505CFZ/2505CFZ 0.1 300 m HCS

Notes 1, 2, 3, 5, 7

Pulse Width Distortion PWD –30 +30 ns 25% to 75% Note 1

with HFBR-1505AFZ/2505AFZ duty cycle

or HFBR-1515BFZ/2515BFZ

Pulse Width Distortion PWD –125 +125 ns arbitrary duty cycle Note 1

with HFBR-1505CFZ/2505CFZ

Notes:

1. With recommended Tx and Rx circuits (60 mA nominal drive current).

2. POF HFBR-ExxyyyZ 0.23 dB/m worst case attentuation.

3. HCS Worst Case Attenuation is 10dB/km (0°C to 70°C) and 12dB/km (-40°C to 85°C).

4. Including a 3 dB optical safety margin accounting for link service lifetime.

5. Including a 2 dB optical safety margin accounting for link service lifetime.

6. Signaling rate DC to 10 MBd.

7. Signaling rate DC to 2 MBd.

CAUTION: The small junction size inherent in the design of these components increases the components’ susceptibility

to damage from electrostatic discharge (ESD). It is advised that normal static precautions be taken in handling and

assembly of these components to prevent damage and/or degradation which may be induced by ESD.

Recommended Chemicals for Cleaning/Degreasing

HFBR-X5X5XFZ Products

Alcohols: methyl, isopropyl, isobutyl.

Aliphatics: hexane, heptane.

Other: soap solution, naphtha.

Do not use partially halogenated hydrocarbons such as

1,1,1 trichloroethane, ketones such as MEK, acetone,

chloroform, ethyl acetate, methylene dichloride, phenol,

methylene chloride or N-methylpyrolldone. Also, Avago

does not recommend the use of cleaners that use

halogenated hydrocarbons because of their potential

environmental harm.

Package Information

All HFBR-X5X5XFZ series transmitters and receivers are

housed in a dual-in-line metal package that is high

strength. The package is designed for auto-insertion and

wave soldering so it is ideal for high volume production

applications.

Handling and Design Information

When soldering, it is advisable to leave the protective

cap on the unit to keep the optics clean. Good system

performance requires clean port optics and cable ferrules

to avoid obstructing the optical path. Clean compressed

air often is su cient to remove particles of dirt; methanol

on a cotton swab also works well.

Speci cations and content subject to change without prior noti cation.

HFBR-15X5XFZ Transmitters

The HFBR-15X5XFZ transmitter incorporates a 650 nm

LED in a metal housing. The high light output power

enables the use of both plastic optical  ber (POF) and

Hard Clad Silica (HCS

). This transmitter can be operated

up to 10 MBd using a simple driver circuit. The HFBR-

1505XFZ is compatible with SMA connectors, while the

HFBR-1515XFZ mates with ST

connectors.

EYE SAFETY: The HFBR-15x5xFZ is a Class 1 LED Product and eye safe when used within the data sheet limits and

under normal operating conditions. This includes all reasonably foreseeable single fault conditions per IEC60825-1

and amendments.

Electrical/Optical Characteristics

-40˚C to +85°C unless otherwise noted.

Parameter Symbol Min. Typ.

[1]

Max. Unit Condition Ref.

Optical Power Temperature P

/T –0.02 dB/˚C

Coe cient

Forward Voltage V

1.8 2.1 2.65 V I

F, dc

= 60 mA Fig. 1

Forward Voltage V

/T –1.8 mV/˚C Fig. 1

Temperature Coe cient

Breakdown Voltage V

3.0 13 V I

F, dc

= –10 μA

Peak Emission Wavelength 

635 650 662 nm Fig. 3

Full Width Half Max FWHM 21 30 nm Fig. 3

Diode Capacitance C

60 pF V

= 0 V, f = 1 MHz

Thermal Resistance 

140 ˚C/W Notes 4, 5

Rise Time (10% to 90%) t

13 ns 10% to 90%,

Fall Time (90% to 10%) t

10 ns

= 60 mA

Absolute Maximum Ratings

Parameter Symbol Min. Max. Unit Reference

Storage and Operating Temperature T

S,O

–40 85 °C

Peak Forward Input Current I

F,PK

90 mA Note 6

Average Forward Input Current I

F, AV G

60 mA

Reverse Input Voltage V

3 V

Lead Soldering Cycle Temp T

SOL

260 °C Note 7, 12

Time 10 s

PIN FUNCTION

CONNECTED TO PIN 4

CONNECTED TO PIN 1

CATHODE

ANODE

BOTTOM VIEW,

HFBR-1505xFZ

SEE NOTE 10

P1-P3 P4-P6 P7-P9 P10-P10

HFBR-1505CFZ

Mfr. #:

Buy HFBR-1505CFZ

Manufacturer:

Broadcom / Avago

Description:

Fiber Optic Transmitters, Receivers, Transceivers Fiber Op Transmitter INTERBUS-S 2 MBd

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

HFBR-1505CFZ

HFBR-1505CFZ

Products related to this Datasheet