THIS DOCUMENT CONTAINS CONFIDENTIAL AND
PROPRIETARY INFORMATION AND ALL DESIGN,
MANUFACTURING, REPRODUCTION, USE, PATENT RIGHTS
AND SALES RIGHTS ARE EXPRESSLY RESERVED BY SAMTEC,
INC. THIS DOCUMENT SHALL NOT BE DISCLOSED, IN WHOLE
OR PART, TO ANY UNAUTHORIZED PERSON OR ENTITY NOR
REPRODUCED, TRANSFERRED OR INCORPORATED IN ANY
OTHER PROJECT IN ANY MANNER WITHOUT THE EXPRESS
WRITTEN CONSENT OF SAMTEC, INC.
PROPRIETARY NOTE
*
*
DO NOT
SCALE FROM
THIS PRINT
-02 THRU -25
(PER ROW)
IPM1-XX-X-XX
C
ROW SPECIFICATION
-D: DOUBLE
-S: SINGLE (SEE SHT 3, FIG. 2 & 3)
No OF POSITIONS
OPTIONS
(LEAVE BLANK FOR NO OPTIONS)
-GP: GUIDE POST (SEE SHT 4, FIG. 5)
(ONLY AVAILABLE ON DOUBLE ROW)
*-SF: SPLASH FLANGE
(COLOR: BLACK;
-03, -04, & -05 TOOLED ONLY;
NOT AVAILABE WITH -S OR -GP)
.258
.021
(TYP)
((NO OF POS X .100) + .070)
-
.008
+
.000
((NO OF POS -1) X .100)
±.002
.1000
.1000
(TYP)
[TOL NON-ACCUM]
"A"
"A"
"B"
"B"
"G"
"G"
'H'
SHOW NUMBER OF POSITIONS
ON THIS SURFACE (SEE NOTE 8)
01 02
C2
C3
C4
C5
.100
(4 PLCS)
"A"
(2 PLCS)
.035
±.010
.050
(2 PLCS)
.120
.08
(TYP)
.080
POSITION 1
INDICATOR TO BE
RAISED .005 MAX
SEE NOTE 3
01
07
12
06
SEE NOTE 11
.05
(2 PLCS)
.05
.350
-
.003
+
.006
C
L
SEE NOTE 2
SEE NOTE 8
SEE NOTE 9
POSITION 1
INDICATOR TO BE
RECESSED .0005 MAX
.100
±.002
.690
-
.004
+
.006
'C'
SECTION "A"-"A"
SCALE 2 : 1
.1020
(TYP)
.1099
(TYP)
.215
.045
.102
(TYP)
.5°
(TYP)
.0450
'F'
'E'
SECTION "B"-"B"
SCALE 3 : 1
C1
FIG 1
IPM1-06-D SHOWN
SHEET OF
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS ANGLES
.XX:
.01 2
.XXX:
.003
.XXXX:
.0015
MATERIAL:
.100 SHROUDED TERMINAL CABLE END
BY:
IPM1-XX-X-XX
DWG. NO.
DESCRIPTION:
DO NOT SCALE DRAWING
D. SCHMELZ
12/04/2008
4
1
SHEET SCALE: 2:1
C:\EnterpriseVault\DWG\MISC\MKTG\IPM1-XX-X-XX-MKT.SLDDRW
NOTES:
1. REPRESENTS A CRITICAL DIMENSION.
2. SAMTEC LOGO SHALL APPEAR AT TWO EQUALLY SPACED LOCATIONS ON
SURFACE SHOWN, APPROXIMATELY .094[2.39] x .055[1.40].
3. ALL MULTIPLE CAVITY MOLDS SHALL IDENTIFY EACH CAVITY WITH A DOT
DESIGNATION LOCATED WHERE SHOWN.
4. ALL IDENTIFICATION MARKS MUST NOT STAND GREATER THAN .002[0.05] OFF THE
SURFACE OF THE PART.
5. MOLDED SURFACES SHALL BE CONSISTENT AND SMOOTH. SURFACES TO BE
FREE OF SCRATCHES, NICKS, SINK AREAS, VOIDS OR OTHER BLEMISHES.
6. MAX ALLOWABLE BOW; TOP/BOTTOM: .0025[0.064], SIDE/SIDE: .0020[0.051].
7. PART TO BE SYMMETRIC ABOUT CENTERLINE WITHIN ±.002 UNLESS INDICATED OTHERWISE.
8. NUMBER OF POSITIONS (PER ROW) TO BE SHOWN IN THIS AREA EXCLUDING 2, 3, & 4 POSITIONS.
SIZE SIMILAR TO POSITION 1 INDICATOR.
9. GATE PADS MUST BE RECESSED .005.
10.END CORES ARE POLARIZED. CONFIRM GEOMETRY RELATIVE TO POSITION 1 INDICATOR & GATE PADS.
11. END POSITIONS TO BE SPECIFIED WHERE SHOWN.
MAX REGRIND: 25%
MAX FLASH ALLOWED: .004
MAX GATE VESTIGE: .002
ZYTEL PA66 101F, COLOR: WHITE
-SF: BLACK
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
REVISION E
