File Name:UHP-500-SPEC 2018-01-16
3.6~4.4V
VOLTAGE ADJ. RANGE
110~140% rated output power
SPECIFICATION
MODEL
DC VOLTAGE
RATED CURRENT
OUTPUT
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE RANGE N
ote.4
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
OVER TEMPERATURE
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSION
OTHERS
NOTE
PACKING
OVERLOAD
OVER VOLTAGE
AC CURRENT (Typ.)
1000ms, 50ms/230VAC 1000ms,50ms/115VAC at full load
90 ~ 264VAC 127 ~ 370VDC
Cold start 30A/115VAC 60A/230VAC
<0.75mA / 240VAC
4.62 ~ 5.46V
-20 ~ +70 (Refer to “Derating Curve")℃
20 ~ 90% RH non-condensing
-40 ~ +85 , 10 ~ 95% RH non-condensing℃
±℃ ℃)0.03%/ (0 ~ 50
10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes
168K hrs min. MIL-HDBK-217F (25 )℃
PF 0.95/230VAC PF 0.98/115VAC at full load≥≥
12ms/230VAC 12ms/115VAC
89%
±1.0%
±0.5%
±2.0%
200mVp-p
4.2V
UHP-500 -4.2
RIPPLE & NOISE (max.)
Note.2
VOLTAGE TOLERANCE Note.3
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : line regulation and load regulation.includes set up tolerance,
4. Derating may be needed under low input voltages. Please check the for more details.derating curve
5. ℃The ambient temperature derating of 3.5 /1000m is needed for operating altitude greater than 2000m(6500ft)
6. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed
that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to EMI testing of component power
supplies. (as available on http://www.meanwell.com)
ENVIRONMENT
PROTECTION
95%
232*81*31mm (L*W*H)
Protection type :Shut down O/P voltage,re-power on to recover
Protection type :Shut down O/P voltage, recovers automatically after temperature goes down
4.85A/115VAC 2.6A/230VAC
RATED POWER(convection)
0.905kg; 16pcs/15.48kg/0.82CUFT
47 ~ 63Hz
Protection type : Hiccup mode, recovers automatically after fault condition is removed
94%
4.5~5.5V
±1.0%
±0.5%
±2.0%
200mVp-p
5V
11.4~12.6V
±0.5%
±0.3%
±1.0%
200mVp-p
12V
14.3~15.8V
200mVp-p
15V
22.8~25.2V
240mVp-p
24V
34.2~37.8V
360mVp-p
36V
45.6~50.4V
360mVp-p
48V
±0.5%
±0.3%
±1.0%
±0.5%
±0.3%
±1.0%
±0.5%
±0.3%
±1.0%
±0.5%
±0.3%
±1.0%
94% 94.5% 95%
90%
39.6 ~46.8V13.2 ~ 15.6V5.75 ~ 6.75V 16.5 ~ 19.5V 26.4 ~ 31.2V 52.8 ~ 62.4V
UHP-500 -5 UHP-500 -12 UHP-500 -15 UHP-500 -24 UHP-500 -36 UHP-500 -48
FUNCTION
REDUNDANT(Optional)
Contact rating(max.):30Vdc/1A resistive load
For parallel connection protection:For parallel applications, when one PSU can not work , the another one will be
automatically enabled. This can prevent the system crash, and provide the reliability of system
DC OK SIGNAL(Optional)
SAFETY STANDARDS
EMC EMISSION
EMC IMMUNITY
Compliance to EN55032,GB/T9254,Class B, EN61000-3-2,-3, EAC TP TC 020
SAFETY &
EMC
(Note.6)
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.25KVAC
I/P-O/P, I/P-FG,O/P-FG:100M Ohms/500VDC/25 / 70%RH℃
Compliance to EN61000-4-2,3,4,5,6,8,11;EN61000-6-2 (EN50082-2), heavy industry level ,criterial A,EAC TP TC 020
UL60950-1,TUV EN60950-1, CCC GB4943, EAC TP TC 004 approved;Design refer to EN60335-1,EN61558-2-16
80A
336W
80A
400W
41.7A
500.4W
33.4A
501W
20.9A
501.6W
13.9A
500.4W 501.6W
10.45A
UHP-500 series
500W Slim Type with PFC Switching Supply
