Technical Note
2/16
BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU
www.rohm.com
2009.03 - Rev.A
© 2009 ROHM Co., Ltd. All rights reserved.
●Operating Range
Parameter Symbol Min. Typ. Max. Unit
Supply voltage Vcc 2.5 3.0 3.45 V
●Electrical Characteristics
[Unless otherwise specified, Typ. : Ta = 25 °C, VCC = 3V]
Parameter Symbol
Typical Values
Unit Measurement Conditions
BH76906
GU
BH76909
GU
BH76912
GU
BH76916
GU
BH76706
GU
Circuit current 1-1 I
CC1-1
15.0 mA In active mode (No signal)
Circuit current 1-2 I
CC1-2
17.0 mA
In active mode
(Outputting NTSC color bar
signal)
Circuit current 2 I
CC2
0.0 A In standby mode
Circuit current 3 I
CC3
- 100 A
In input mode (Applying B3 =
1.5 V)
Standby switch input current
High Level
I
thH1
45
-
A Applying B3 = 3.0 V
Standby switch switching voltage
High Level
V
thH1
1.2V min V Active mode
Standby switch switching voltage
Low Level
V
thL1
0.45Vmax V Standby mode
Standby switch outflow current
High Level
I
thH2
-
0
A Applying B3 = 3.0 V
Standby switch outflow current
Middle Level
I
thM2
8
A Applying B3 = 1.5 V
Standby switch outflow current
Low Level
I
thL2
23
A Applying B3 = 0 V
Mode switching voltage
High Level
V
thH2
VCC
-0.2
(MIN.)
V Standby mode
Mode switching voltage
Middle Level
V
thM2
VCC/2
(TYP.)
V Input mode
Mode switching voltage
low Level
V
thL2
0.2
(MAX.)
V Active mode
Voltage gain G
V
6.0 9.0 12.0 16.5 6.0 dB Vo=100kHz, 1.0Vpp
Maximum output level Vomv 5.2 Vpp f=10kHz,THD=1%
Frequency characteristic 1 G
f1
-0.2 -0.2 dB f=4.5MHz/100KHz
Frequency characteristic 2 G
f2
-1.5 -1.4 dB f=8.0MHz/100KHz
Frequency characteristic 3 G
f3
-26 -28 dB f=18MHz/100KHz
Frequency characteristic 4 G
f4
-44 -48 dB f=23.5MHz/100KHz
Differential gain D
G
0.5 %
V
o=1.0Vp-p
Inputting standard staircase
Signal
Differential phase D
P
1.0 deg
V
o=1.0Vp-p
Inputting standard staircase
signal
Y signal to noise ratio SN
Y
+74 +73 +70 +70 +74 dB
100 kH
z~6MHz band
Inputting 100% white video signal
C AM signal to noise ratio SN
CA
+77 +76 +75 +75 +77 dB
100~500 kHz band
Inputting 100% chroma video signal
C PM signal to noise ratio SN
CP
+65 dB
100~500 kHz band
Inputting 100% chroma video signal
Current able to flow into output pin lextin 30 mA
Applying 4.5 V to output pin
through 150 Ω
Output DC offset Voff ±50max mV
With no signal
Voff = (Vout pin voltage) ÷ 2
Input impedance Rin 150 k
Measure inflowing current when
applying A3 = 1 V
Output pin shunt switch
on resistance
Ron - 3