5/8" [15.88 mm] Thru Hole
37
Permanent Mount with Hardware
Rugged Insert Molded Design
High Strength Impact Resistant ABS Radome
Standard N-Female Termination
ground plane or surface
and must get full compression on the
O-ring must be in place during installation
Protective cap during shipping
Remove before installation
87
111
Electrical Note:
Packaging Note:
Mechanical Note:
Recommended Mounting Conditions:
Surface should be as flat and clean as possible
Hole should be centered as much as possible
R. HARO
23SEP14
3.
N/A
Laird Technologies SKU: TRA6927M3PWN-001
23SEP14
2.
Units per Package: 1
B. HOFFMAN
Package Label: Printed Bag
N/A
1.
4.
Package: S1136
REVISIONS
ZONE REV. DESCRIPTION DATE DRAWN BY ECR NUMBER
ALL AA INITIAL RELEASE 23SEP14 BPH ECN-IAS-03118
Frequency: VSWR1.
698 - 806 MHz: < 2.5 : 1.0
806 - 960 MHz: < 2.0 : 1.0
1710 - 2700 MHz: < 2.0:1.0
Nominal Impedance: 50 OHM2.
Polarization: Vertical3.
Pattern: Omnidirectional4.
Ground Plane: No Ground Plane Required5.
Overall Height: ~ 87 mm from Mounting Surface1.
Weight: 0.42 lbs2.
IP Rating: IP673.
Operating temp: -35 C to +65 C4.
Storage Temp: -45 C to +65 C5.
Color: White6.
Mounting: Permanent Mount (See "Recommended Mounting Conditions")7.
Installation Torque: 4 - 6 ft*lbs on Nut8.
REPRODUCTION, USE, DISCLOSURE OR TRANSMITTAL OF ALL OR ANY PART OF THIS DOCUMENT IS PROHIBITED
M:\18 - ARAS\Ben\ARAS WD\TRA6927 - NGP\M&O\
THIRD ANGLE
Notes:
THE COMPONENTS(S), INCLUDING ANY PLATING, FINISHES, COATINGS, CHEMICALS AND SURFACES TREATMENTS,
PROJECTION
SPECIFICATION LT-GES-001, (GENERAL SPECIFICATION FOR THE ENVIRONMENT) IS READILY AVAILABLE UPON
SUPPLIED IN THIS DOCUMENT/DRAWING MUST CONFORM AND COMPLY WITH THE LATEST ISSUE OF LAIRD
COPYRIGHT, LAIRD TECHNOLOGIES 2008, ALL RIGHTS RESERVED.
TRA6927M3PWN-001MO
REQUEST FROM THE SUPPLIER.
GUIDE STANDARD JIG-101, APRIL 2005. THE COMPONENT(S) IN THIS DOCUMENT/DRAWING MAY BE SUBJECT TO
A FULL COMPOUND ANALYSIS FOR PROOF OF COMPLIANCE. THE LATEST ISSUE OF LAIRD TECHNOLOGIES
INTERPRET DIMENSIONING AND
USA
EXCEPT TO THE EXTENT APPROVED IN WRITING BY AN AUTHORIZED REPRESENTATIVE OF LAIRD TECHNOLOGIES.
LAIRD TECHNOLOGIES RESERVES ALL RIGHTS UNDER PATENTS, TRADEMARKS, COPY RIGHTS AND TRADE SECRETS.
TOLERANCING IN ACCORDANCE
WITH ASME Y14.5M-1994
DO NOT SCALE DRAWING
TECHNOLOGIES SPECIFICATION LT-GES-001, WHICH FULLY INCLUDES BUT IS NOT LIMITED TO ALL CONTENTS
OF EU DIRECTIVES 2002/96/EC (RoHS DIRECTIVE), AS WELL AS INCLUDES REQUIREMENTS OF THE JOINT INDUSTRY
1751 WILKENING COURT
SCHAUMBURG, IL 60173
UNLESS OTHERWISE NOTED, THIS DOCUMENT CONTAINS LAIRD TECHNOLOGIES CONFIDENTIAL INFORMATION.
TOLERANCES UNLESS OTHERWISE
SPECIFIED
DIMENSIONS ARE IN MILLIMETERS
ANGLE: 30'
0 PLACE DECIMAL: 0.5
1 PLACE DECIMAL: 0.25
2 PLACE DECIMAL: 0.13
NOTES:
WEIGHT:
SIZE
AA
9
SHEET 1 OF 1
6
D
C
B
A
E
F
G
H
E
A
B
C
D
F
54321 7 10 11 12
1 2 3 4 5 6 7 8
8
G
TRA6927M3PWN-001
A2
SCALE:
DWG NO.
TITLE:
REV
MATERIAL:
DATEAPPROVALS
ME:
FINISH:
Prod:
EM:
RF:
PREVIOUS#
MOUNTING & OUTLINE
