Tyco Electronics Corporation
300 Constitution Drive Faraday Road 3816 Noborito, Tama-ku Asia Pacific Headquarters
Menlo Park, CA 94025-1164 Dorcan, Swindon, SN3 5HH Kawasaki, Kanagawa 214-8533 26 Ang Mo Kio, Industrial Park 2
USA United Kingdom Japan Singapore 569507
Tel:(800) 926-2425 (US & Canada) Tel: +44 1793 528171 Tel: +81 44 900 5102 Tel: +65 4866 151
Tel:+1 (650) 361-3860 (All other countries)
For more information about this product visit www.tycoelectronics.com
All information, including illustrations, is believed to be reliable. Users, however, should independently evaluate the suitability of each product for their application. Tyco Electronics Corporation makes
no warranties as to the accuracy or completeness of the information, and disclaims any liability regarding its use. Tyco Electronics Corporation’s only obligations are those in the Standard Terms and
Conditions of Sale for these products and in no case will Tyco Electronics Corporation be liable for any incidental, indirect, or consequential damages arising from the sale, resale, use, or misuse of the
product. Tyco Electronics Corporation’s Specifications are subject to change without notice. In addition, Tyco Electronics Corporation reserves the right to make changes in materials or processing
without notification to the Buyer which do not affect compliance with any applicable specification.
Specification values
Property Unit Requirement Method of test
Material Dimensions mm (inches) See Reverse ASTM D 2671
Longitudinal change percent +1, -10 ASTM D 2671
Tensile strength psi (Mpa) 1500 (10.3) minimum ASTM D 412
Ultimate elongation percent 225 minimum ASTM D 412
Tensile stress at 200% elongation psi (Mpa) 1500 (10.3) maximum AMS-DTL-23053
Restricted shrinkage No cracks AMS-DTL-23053
(30 minutes at 135°C/
275°F)
Followed by test for:
Voltage withstand Pass
Low temperature flexibility No cracks AMS-DTL-23053
(4 hours at -70°C/-94°F)
Heat shock No cracks, flowing or AMS-DTL-23053
(4 hours at 200°C/392°F) dripping
Heat resistance ASTM D 2671
(168 hours at 121°C/
250°F)
Followed by tests for:
Tensile strength psi (Mpa) 1200 (8.3) minimum ASTM D 412
Ultimate elongation percent 175 minimum ASTM D 412
Dielectric strength volts/mil
(kv/mm) Sizes up to 7/8: ASTM D 2671
300
(11.8) minimum
Sizes 1 and larger:
200 (7.8) minimum
Electrical Dielectric strength volts/mil (kv/mm) Sizes up to 7/8: ASTM D 2671
300
(11.8) minimum
Sizes 1 and larger:
200 (7.8) minimum
Volume resistivity ohm-cm 1 x 10
11
minimum ASTM D 876
Chemical Copper mirror corrosion No pitting or AMS-DTL-23053
(16 hours at 150°C/302°F) corrosion
Copper contact corrosion No pitting or blackening AMS-DTL-23053
(16 hours at 150°C/302°F) of copper
Flammability Self-extinguishing in ASTM D 2671
15 seconds; 3 inches Procedure A
maximum burn length
Fungus resistance No growth ASTM G 21
Water absorption percent 1.0 maximum ASTM D 570
(24 hours at 23°C/73°F)
` Fluid resistance AMS-DTL-23053
(24 hours at 23°C/
73°F) in:
JP-8 fuel (MIL-T-83133)
Hydraulic fluid (MIL-H-5606)
Lubricating oil (MIL-L-7808)
Lubricating oil (MIL-L 23699)
Salt water (5% salt)
Anti-icing fluid (MIL-A-8243)
Followed by tests for:
Tensile strength psi (Mpa) 1000 (6.9) minimum ASTM D 412
Ultimate elongation percent 175 minimum ASTM D 412
Dielectric strength volts/mil (kV/mm) 250 (9.8) minimum ASTM D 2671
Note: Consult RW-3030 for specific details about test procedures.
Raychem is a trademark of Tyco Electronics Corporation.
© 2002 Tyco Electronics Corporation Printed in USA 1654103-FP-Revised 04/04