OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

HFBR-5911ALZ

P1-P3P4-P6P7-P9P10-P12
4
Table 1 - Supported LinksfromIEEE802.3
Fiber Type
Modal bandwidth @ 850 nm
(min. overlled launch) (MHz - km)
Link length
UnitsMinimum Maximum
62.5µmMMF 160 2 220 m
62.5µmMMF 200 2 275 m
50µmMMF 400 2 500 m
50µmMMF 500 2 550 m
Parameter Symbol Minimum Typical Maximum Units Reference
Storage Temperature T
S
-40 +100 °C
Operating Temperature - Case T
C
-10 +85 °C
AqueousWashPressure 110 psi
Relative Humidity - non condensing RH 5 95 %
Supply Voltage V
CC
-0.5 3.63 V
Voltage to any pin -0.5 3.63 V
TTL Transmit Disable Current I
I
-3.0 3.0 mA
Parameter Symbol Minimum Typical Maximum Units Reference
Temperature - Case
HFBR-5911LZ
HFBR-5911ALZ
T
C
T
C
0
-10
+70
+85
°C
°C
11
Supply Voltage V
CC
3.14 3.47 V
Input Data Dierential Voltage 0.4 1.6 V
TTL Transmit Disable Input Voltage - Low V
IL
0.8 V
TTL Transmit Disable Input Voltage - High V
IH
V
CC
-1.3 V
CC
V
TTL Transmit Disable Input Current I
I
-1.0 400 mA
Notes:
1. Operatingthetransceiverbeyond+70°Cforextendedperiodscanadverselyaectdevicereliability.
Table 3 - Recommended Operating Conditions
The Recommended Operating Conditions are those values outside of which device reliability and performance to data sheet are
not implied, and damage to the device may occur over an extended period of time. See Reliability Data Sheet for specic reliabil-
ity performance.
Table 2 - Absolute Maximum Ratings
The Absolute Maximum Ratings are those values beyond which damage to the device may occur if these limits are exceeded for
other than a short period of time. See Reliability Data Sheet for specic reliability performance.
5
Pin Symbol Functional Description Logic Reference
MS MS Mounting Stud n/a 4
HL HL Housing Lead n/a 5
1 Vee
r
Receiver Signal Ground n/a
2 Vcc
r
ReceiverPowerSupply n/a
3 SD Signal Detect TTL 6
4 RD- Receiver Data Out Bar PECL 7
5 RD+ Receiver Data Out PECL 7
MS MS Mounting Stud n/a 4
HL HL Housing Lead n/a 5
6 Vcc
t
TransmitterPowerSupply n/a
7 Vee
t
Transmitter Signal Ground n/a
8 T
Dis
Transmitter Disable TTL 8
9 TD+ Transmitter Data In PECL 9
10 TD- Transmitter Data In Bar PECL 9
Parameter Symbol Minimum Typical Maximum Units Reference
Transmitter Supply Current I
CC
Tx 55 75 mA
PowerDissipation P
DISS
180 260 mW
Data Input Dierential Voltage V
IH
-V
IL
400 1600 mV
PowerSupplyNoiseRejection PSNR 100 mV
P-P
10
Notes:
4. Themountingstudsprovidemechanicalattachmenttothecircuitboardandconnectiontotheequipmentchassisground.TheMSviaholes
must not be tied to signal ground and may be tied to chassis ground.
5. The housing leads provide additional signal grounding. The HL via holes must be tied to signal ground.
6. Normaloperation: Logic“1”output
No-signalcondition: Logic“0”output
7. ACcoupleddierentialoutput.LVPECLsignal.InterfacingICsmayrequireinternalbiasing.
8. TransmitterOutputDisabled: (Vcc
t
-1.3 V)<V<Vcc
t
TransmitterOutputEnabled:Vee
t
< V < (Vee
t
+0.8V)
9. AC coupled dierential input, no external termination required. 100 ohm internal termination provided.
10. Tested with a 100 mV
P-P
sinusoidal signal in the frequency range from 10 KHz to 2 MHz on the V
CC
supply with the recommended power sup-
plylter(withC8)inplace.Typically,achangeinsensitivityoflessthan1dBisexperienced.
Table 5 - Transmitter Electrical Characteristics
HFBR-5911LZ (T
C
=0ºCto+70ºC,V
CC
=3.14Vto3.47V)
HFBR-5911ALZ (T
C
=-10°Cto+85°C,V
CC
=3.14Vto3.47V)
Figure 1 - Pin out drawing
Table 4 - Pin Description
6
Table 6 - Transmitter Optical Characteristics
HFBR-5911LZ (T
C
=0ºCto+70ºC,V
CC
=3.14Vto3.47V)
HFBR-5911ALZ (T
C
=-10°Cto+85°C,V
CC
=3.14Vto3.47V)
Parameter Symbol Minimum Typical Maximum Units Reference
OpticalOutputPower
62.5µm
50µm
P
OUT
-9.5
-9.5
-1.5
-1.5
dBm avg. 11
Tx_DisableOpticalOutputPower P
OUTDIS
-30 dBm avg. 11
Optical Extinction Ratio ER 9 dB 12
Center Wavelength l
C
830 850 860 nm
Spectral Width - rms
s
0.85 nm rms
Optical Rise Time t
r
0.26 ns 13
Optical Fall Time t
f
0.26 ns 13
RIN
12
-117 dB/Hz
CoupledPowerRatio CPR 9 dB 14
ContributedTotalJitter TJ 2270.284 psUI 15
Parameter Symbol Minimum Typical Maximum Units Reference
Receiver Supply Current I
CC
RX 135 mA
PowerDissipation P
DISS
230 470 mW
PowerSupplyNoiseRejection PSNR 100 mV
P-P
16
Data Output Dierential Voltage V
OH
-V
OL
0.4 1.3 V
Data Output Rise Time t
r
0.4 ns
Data Output Fall Time t
f
0.4 ns
TTL Signal Detect Output Voltage - Low V
OL
0.6 V
TTL Signal Detect Output Voltage - High V
OH
2.2 V
Notes:
11.ThemaximumOpticalOutputPowercomplieswithIEEE802.3andisClass1lasereyesafe.
12.OpticalExtinctionRatioisdenedastheratiooftheaverageopticalpowerofthetransmitterinthehigh(“1”)statetothelow(“0”)state.The
transmitterisdrivenwithaGigabitEthernet1250MBd8b/10bencodedserialdatapattern.OpticalExtinctionRatioisexpressedindecibels
(dB)bytherelationship10log(P
high
avg/P
low
avg).
13.OpticalRiseandFallTimesare20-80%value.Lasertransmitterpulsecharacteristicsaretypicallyspeciedbyaneyediagram-seeFigure6.
The characteristics include rise time, fall time, pulse overshoot, pulse undershoot and ringing, all of which are controlled to prevent excessive
degradation of receiver sensitivity. These parameters are specied by the referenced Gigabit Ethernet eye diagram using the required lter.
TheoutputopticalwaveformcomplieswiththerequirementsoftheeyemaskdescribedinIEEE802.3section38.6.10andFigure38-2.
14.CPRismeasuredinaccordancewithEIA/TIA-526-14AasreferencedinIEEE802.3section38.6.10.
15.MeasuredatTP2.TPreferstothecompliancepointspeciedbyIEEE802.3,section38.2.1.
16.Testedwitha100mV
P-P
sinusoidal signal in the frequency range from 10 Hz to 2 MHz on the V
CC
supply with the recommended power sup-
plylter(withC8)inplace.Typically,achangeinsensitivityoflessthan1dBisexperienced.
Table 7 - Receiver Electrical Characteristics
HFBR-5911LZ (T
C
=0ºCto+70ºC,V
CC
=3.14Vto3.47V)
HFBR-5911ALZ (T
C
=-10°Cto+85°C,V
CC
=3.14Vto3.47V)
P1-P3P4-P6P7-P9P10-P12

HFBR-5911ALZ

Mfr. #:
Buy HFBR-5911ALZ
Manufacturer:
Description:
Fiber Optic Transmitters, Receivers, Transceivers 1.25G MM 2X5 3.3V SF F/LC/ExTp RoHS
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet