1
DATASHEET
To request the full datasheet, please visit www.intersil.com/products/tw9992
Low Power NTSC/PAL Video Decoder with Differential
CVBS Inputs and MIPI-CSI2 Output Interface
TW9992
The TW9992 is a low power NTSC/PAL analog video decoder
that is designed for automotive applications. It supports
single-ended, differential and pseudo differential composite
video inputs. Integrated short-to-battery and short-to-ground
detection, advanced image enhancement capabilities such as
the programmable Automatic Contrast Adjustment (ACA) and
the MIPI-CSI2 output interface make the TW9992 an ideal
solution for demanding automotive camera applications.
Features
Analog Video Decoder
• Software selectable analog input control allows for
combinations of single-ended CVBS, and differential CVBS
• Built-in analog anti-alias filter
• Two 10-bit ADCs and analog clamping circuit
• Fully programmable static gain or automatic gain control for
the Y channel
• Programmable white peak control for the Y channel
• 4-H adaptive comb filter Y/C separation
• PAL delay line for color phase error correction
• Digital subcarrier PLL for accurate color decoding
• Digital horizontal PLL for synchronization processing and
pixel sampling
• Advanced synchronization processing and sync detection for
handling nonstandard and weak signal
• Automatic color control and color killer
• Chroma IF compensation
• VBI slicer supporting industrial standard data services
• VBI data passthrough, raw ADC data output
•Programmable output cropping
Video Processing
• Automatic Contrast Adjustment (ACA)
• RGB565
• Programmable hue, brightness, saturation, contrast and
sharpness.
• Image enhancement with peaking and CTI
MIPI Output
• MIPI 1.1 compliant unidirectional output format
• YUV 422 or RGB565 output format
Digital Output
• Output voltage 1.8V to 3.3V with 3.3V tolerance
Miscellaneous
• Low power consumption: 100mW typical
• Power save and Power-down mode
• Short-to-battery detection test
•Short-to-ground detection test
• Two-wire MPU serial bus interface
• Supports real time control interface
• Single 27MHz crystal for all operations
• Supports 24.54MHz and 29.5MHz crystal for high resolution
square pixel format decoding
•3.3V tolerant I/O
• 1.8V/3.3V power supply
• 32 Ld QFN (WQFN with wettable flanks)
• TW9992AT-NA1-GE is AEC-Q100
qualified
FIGURE 1. TW9992 FUNCTIONAL BLOCK DIAGRAM
MUX
YIN0/
YIN1/YIN0-
YIN2 / YIN2+ / DIAG0
YIN4 /
YIN3 / YIN2-
YIN5 / YIN4-
YIN6 /
YIN7 / YIN6-
DIAG1
DIAG2
RSTB
PDN
SCLK
SDAT
STB/STG
DETECT ION
I
2
C
DETECT ION
OSC
REGISTER
FILES
PLL
ANTI-ALIASING
FILTER
AGC
10-bit ADC
4H COMB
FILTER
DECODER
AUTOMATIC
CON TRA ST
ADJUST MENT
FORMAT
CON VER TER
MIPI PROTOCOL
CON TROLL ER
MIPI
SERIALIZER
MIPI D-PHY
GP0
GP1
GP2
INTREQ
MIPID-
MIPID+
MIPICLK-
MIPICLK+
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774
| Copyright Intersil Americas LLC 2015, 2016. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
September 1, 2016
FN8722.1