OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

SLI-560UT3F

P1-P3P4-P6P7-P9P10-P12
[SLI-560x/SLA-560x/SLA560x series]
　　　　
[Data Sheet]
■Part No. Construction
*"-"will be taken out for emitting color Special Code will be applied for Chromaticity rank Rank sign
WB/B/E series. Emitting color WB/B/E series. (for white LED） (Brightness Rank)*
Series name Package type Emitting Color Resin Color Taping Specification
V R
U U
U2 Y
D G
Y C
Y2 RC
M T
P
E
B
*Concerning the Brightness rank.
WB
*Please refer to the rank chart above for
luminous intensity classification.
*Part name is individual for each rank.
*When shipped as sample,the part name will
be a representative part name.
General products are free of ranks.
Please contact sales if rank appointment
is needed.
SLR 1-Die Circular Type LED Lamps
1-Die Circular Type Low Current High Brightness LED Lamps
Red
6
SLA
SLI
S L I － 5 XK
1-Element straight bulk
See Taping specifications
3F
T□□
SLD
1-Die Oval Type High Brightness LED Lamps
Orange
<Yellowish green>DiffusedColored
2T
<Red>DiffusedColored
<Orange>DiffusedColored
30 U T
1-Die Circular Type High Brightness LED Lamps
Red
Transparent Colored
Yellow
Yellowish green
Transparent Coloreless
Red
<Yellow>DiffusedColored
Green
Green
Blue
White
Yellow
＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿
www.rohm.com
©2016 ROHM Co., Ltd. All rights reserved
7/10
2017.9 - Rev.005
[SLI-560x/SLA-560x/SLA560x series]
　　　　
[Data Sheet]
Visual light emitting diode does not contain reinforcement materials such as glass fillers.
Therefore if sudden thermal and mechanical shock are given, destruction or inferiority of luminous
intensity may occur. Please take care of the handling.
■ATTENTION POINTS IN HANDLING
■FIXATION METHOD
１．ATTENTION POINTS
　(1) Please do not give excessive heat over storage temperature to resin.
　　In case that the product has to be heated in oven for the glue fixing of surface mount parts,
　　this LED should be mounted after the glue fixing.
　(2) Please avoid stress to resin at high temperature.
２． TERMINATION PROCESSING
　(1) In case of termination processing, please fix the
　　space or lead pins space after forming to avoid the physical stress on resin.
　(2) Using spacer between LEDʼs body and PCB is recommended.
　　In case of direct mount on PCB(SLR/SLI-343 series), please take care about clinch of LED pins
　　to avoid the remained stress and solder heat stress.
　　
Enough evaluation is requested before deciding assembly and soldering conditions.
Please consult with us if any problems in the evaluation stage.
　　termination
　(2) Processing position, and process the reverse side
　　of LED body.
　　If stress is given during processing, It may cause
　　non-lighting failure.
　(3) Please process before soldering.
３． ASSEMBLY ON PC BOARD
　(1) In case of soldering on PCB, If the operation is done with stress, it may cause non-lighting
　　failure during soldering or using. Please design the through-holes of PCB suitable for lead pins
＜Good＞ ＜No good＞
To be fixed To be fixed
＜Good＞ ＜No good＞＜Good＞
＜2 lead pins type＞
＜3 lead pins type＞
Min.15°
Min.45°
Die bonding side
＜2 lead pin type＞
Min.15°
Min.45°
Die bonding side
Min.45
＜3 lead pin type＞
＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿
www.rohm.com
©2016 ROHM Co., Ltd. All rights reserved
8/10
2017.9 - Rev.005
[SLI-560x/SLA-560x/SLA560x series]
　　　　
[Data Sheet]
　so please check the solvent before actual use.
Cleaning by solvent
Cleaning time
：Max. 3min
Soldering Iron
Max. 400℃
3sec Max.
The iron should not touch the LEDʼs body.
　The recommendable cleaning solvent is alcoholic one such as isopropyl alcohol.
＜RECOMMENDABLE CLEANING CONDITIONS＞
METHOD
CONDITIONS
Cleaning by solvent
■ATTENTION ON STORAGING
Immersion time
：Max. 3min
Ultrasonic out
：Max. 15W/Liter
　　luminous intensity may occur.
Pre-heat
Max. 100℃
60sec Max.
－
４．SOLDERING（Sn-3Ag-0.5Cu）
　(1) Please make soldering rapidly under the following temperature and time conditions.
　(2) Please avoid stress to LED lamp during soldering.
　(3) In case of double peak flow soldering, the temperature gap during 1st and 2nd soldering to be
Soldering Dip
Soldering Bath
Max. 265℃ 5sec Max.
In case of double peak flow soldering, the operation
time is counted from the beginning of 1st peak
to the end of 2nd peak.
　　less than 100 degree C.
＜Recommendable soldering conditions＞
ARTIICLE
　(1) Lead pins may corrode if it is stored in the environment of high temperature and humidity
　　and lead to defective soldering.
　(2) In case of soldering after LEDʼs body absorb moisture highly, destruction or inferiority of
５．CLEANING
　In case of cleaning, some solvents may cause damage of resin or cause non-lighting failure,
Temperature of solvent
：Max. 45℃
　　Our recommendation is as follow :
　Storage in dry box is most desirable, but if it is not possible, we recommend following conditions.
＜RECOMMENDABLE STORAGE CONDITIONS＞
CONDITIONS
5〜30℃
Max.60%RH
Within 1 year
Poor storage conditions may cause some failure as bellow.
ARTICLE
Temperature
Humidity
Expiration Date
６．RECOMMENDABLE ROUND PATTERN
　　Round pattern depends on the material PCB, density and circuit arrangement.
OPERATION TIME
Remarks
SOLDERINGTEMP
<2 lead pin type> <3 lead pin type/2.5mm pitch>
＜3 lead pin type/2.0mm pitch>
1.5
±0.1
1.0
2.0
2.0
φ2.0
2.0
2.5
or
5.0
±0.1
1.0
2.0
±0.1
1.0
2.5
2.5
＊Unit : mm
＊Lead types : □0.4mm
□0.5mm
＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿
www.rohm.com
©2016 ROHM Co., Ltd. All rights reserved
9/10
2017.9 - Rev.005
P1-P3P4-P6P7-P9P10-P12

SLI-560UT3F

Mfr. #:
Buy SLI-560UT3F
Manufacturer:
ROHM Semiconductor
Description:
Standard LEDs - Through Hole RED HIGH BRIGHT
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet