OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

67-31H/RSC-AZ0Z2B9Z5/BT

P1-P3P4-P6P7-P9P10-P11
EVERLIGHT ELECTRONICS CO., LTD.
Technical Data Sheet
Power Top View LEDs with Lens
67-31H/RSC-AZ0Z2B9Z5/BT
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 10 of 11
Device No. :
DSE-0000675 Prepared date: 30-Dec-2008 Prepared by:Ruby Yang
Precautions for Use
1. Over-current-proof
Customer must apply resistors for protection, otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package: The LED should be kept at 30℃ or less and 90%RH or less.
2.3 After opening the package: The LED floor life is 1 year under 30℃ or less and 60% RH
or less. If unused LED remain, it should be stored in moisture proof packages.
2.4 If the moisture absorbent material (silica gel) has faded away or the LED have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
120 Sec. Max.
1~5 °C / Sec.
Pre-heating
180~200°C
60 Sec. Max.
Above 220°C
260°C. Max.
10 Sec. Max.
1~5 °C / Sec.
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
EVERLIGHT ELECTRONICS CO., LTD.
Technical Data Sheet
Power Top View LEDs with Lens
67-31H/RSC-AZ0Z2B9Z5/BT
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 11 of 11
Device No. :
DSE-0000675 Prepared date: 30-Dec-2008 Prepared by:Ruby Yang
4. Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more
intervals, and do soldering of each terminal. Be careful because the damage of the product is
often started at the time of the hand solder.
5. Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable,
a double-head soldering iron should be used. It should be confirmed beforehand whether the
characteristics of the LEDs will or will not be damaged by repairing.
EVERLIGHT ELECTRONICS CO., LTD. Tel: 886-2-2267-2000, 2267-9936
Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: 886-2267-6244, 2267-6189, 2267-6306
Tucheng, Taipei 236, Taiwan, R.O.C http://www.everlight.com
P1-P3P4-P6P7-P9P10-P11

67-31H/RSC-AZ0Z2B9Z5/BT

Mfr. #:
Buy 67-31H/RSC-AZ0Z2B9Z5/BT
Manufacturer:
Everlight
Description:
Standard LEDs - SMD PLCC LED
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet