5962-9325801M2A Datasheet 5962-9325801M2A, 5962-9325801MCA | P1-P3

REVISIONS

LTR DESCRIPTION DATE (YR-MO-DA) APPROVED

Change to the supply current test, I

, in table I. Update boilerplate. - rrp

99-11-16 R. MONNIN

B Add radiation hardness requirements. Add case outline D. Add table IIB. - rrp 00-05-05 R. MONNIN

Add footnote to the supply voltage test in section 1.3. Add footnote to the

supply current and power supply rejection ratio test in table I. Update

boilerplate. – rrp

01-10-17 R. MONNIN

Change to the post irradiation test limits in table I for I

, I

, A

, and I

Removed accelerated aging and dose rate burnout provisions in

section 4. – rrp

01-11-15 R. MONNIN

E Added subgroup 4 to table IIA under group E end-point for device class V. – gt 03-03-11 R. MONNIN

F Drawing updated to reflect current requirements. - rrp 05-09-07 R. MONNIN

Delete footnote 2/ from section 1.3. Delete footnote 5/ from Table I.

These footnotes were incorrectly added under revision C. - ro

10-04-22 C. SAFFLE

Add footnote 4/ to the Large signal voltage gain (A

) test under the condition

column with V

= 5 V as specified in Table I. Delete figure 2 radiation

exposure circuit. Make change to paragraph 3.2.3. - ro

14-12-08 C.SAFFLE

Delete footnote 4/ from the Output voltage swing test under the condition

column with V

= 15 V as specified in Table I. - ro

15-04-08 C. SAFFLE

REV

SHEET

REV

SHEET

REV STATUS REV J J J J J J J J J J J

OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11

PMIC N/A PREPARED BY

RICK C. OFFICER

DLA LAND AND MARITIME

COLUMBUS, OHIO 43218-3990

http://www.landandmaritime.dla.mil

STANDARD

MICROCIRCUIT

DRAWING

THIS DRAWING IS AVAILABLE

FOR USE BY ALL

DEPARTMENTS

AND AGENCIES OF THE

DEPARTMENT OF DEFENSE

CHECKED BY

RAJESH R. PITHADIA

APPROVED BY

MICHAEL A. FRYE

MICROCIRCUIT, LINEAR, RADIATION

HARDENED, PRECISION, HIGH SPEED, QUAD

OPERATIONAL AMPLIFIER, MONOLITHIC

SILICON

DRAWING APPROVAL DATE

94-03-02

AMSC N/A

REVISION LEVEL

SIZE

CAGE CODE

67268

5962-93258

SHEET 1 OF 11

DSCC FORM 2233

APR 97 5962-E182-15

STANDARD

MICROCIRCUIT DRAWING

SIZE

5962-93258

DLA LAND AND MARITIME

COLUMBUS, OHIO 43218-3990

REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

1. SCOPE

1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device class Q and M)

and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or

Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN.

1.2 PIN. The PIN is as shown in the following example:

5962 R 93258 01 V C A

Federal

stock class

designator

RHA

designator

(see 1.2.1)

Device

type

(see 1.2.2)

Device

class

designator

Case

outline

(see 1.2.4)

Lead

finish

(see 1.2.5)

\ / (see 1.2.3)

Drawing number

1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are

marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A

specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.

1.2.2 Device type(s). The device type(s) identify the circuit function as follows:

Device type Generic number Circuit function

01 OP467 High speed, quad, operational amplifier

1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as

follows:

Device class Device requirements documentation

M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-

JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A

Q or V Certification and qualification to MIL-PRF-38535

1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:

Outline letter Descriptive designator Terminals Package style

C GDIP1-T14 or CDIP2-T14 14 Dual-in-line

D GDFP1-F14or CDFP2-F14 14 Flat pack

2 CQCC1-N20 20 Square leadless chip carrier

1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535,

appendix A for device class M.

STANDARD

MICROCIRCUIT DRAWING

SIZE

5962-93258

DLA LAND AND MARITIME

COLUMBUS, OHIO 43218-3990

REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

1.3 Absolute maximum ratings. 1/

Supply voltage (V

) ................................................................................................. 18 V

Differential input voltage 2/ ....................................................................................... 26 V

Input voltage 2/ ......................................................................................................... 18 V

Output short-circuit duration ...................................................................................... Limited

Storage temperature range ....................................................................................... -65C to +175C

Lead temperature (soldering, 60 seconds) ................................................................ +300C

Junction temperature (T

) .......................................................................................... -65C to +175C

Thermal resistance, junction-to-case (

) ................................................................ See MIL-STD-1835

Thermal resistance, junction-to-ambient (

Case C ................................................................................................................... 94C/W

Case D ................................................................................................................... 140C/W

Case 2 .................................................................................................................... 78C/W

1.4 Recommended operating conditions.

Supply voltage (V

) ................................................................................................. 15 V

Ambient operating temperature range (T

) ............................................................... -55C to +125C

1.5 Radiation features.

Maximum total dose available (dose rate = 50 – 300 rads(Si)/s) ............................... 100 krads 3/

2. APPLICABLE DOCUMENTS

2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part

of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the

solicitation or contract.

DEPARTMENT OF DEFENSE SPECIFICATION

MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.

DEPARTMENT OF DEFENSE STANDARDS

MIL-STD-883 - Test Method Standard Microcircuits.

MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.

DEPARTMENT OF DEFENSE HANDBOOKS

MIL-HDBK-103 - List of Standard Microcircuit Drawings.

MIL-HDBK-780 - Standard Microcircuit Drawings.

(Copies of these documents are available online at http://quicksearch.dla.mil or from the Standardization Document Order

Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

______

1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the

maximum levels may degrade performance and affect reliability.

2/ For supply voltages less than 18 V, the absolute maximum input voltage is equal to the supply voltage.

3/ These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects.

Radiation end point limits for the noted parameters are guaranteed only for the conditions specified in MIL-STD-883,

method 1019, condition A.

P1-P3 P4-P6 P7-P9 P10-P12

5962-9325801M2A

Mfr. #:

Buy 5962-9325801M2A

Manufacturer:

Analog Devices Inc.

Description:

High Speed Operational Amplifiers QUAD LO NOISE HI Spd IC

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

5962-9325801M2A

5962-9325801M2A

Products related to this Datasheet