4400-900 Datasheet 4401-010, 4400-034, 4400-016 | P13-P14

The products listed in this catalog are only a few of the thou-

sands of variations that TUSONIX produces. For custom

component design, please contact the factory direct.

Product Installation Recommendations and EIA codes

PRODUCT INSTALLATION RECOMMENDATIONS

The components in this catalog are manufactured with ceramic dielectrics. To minimize possible damage to the components

during installation, the recommendations below should be followed. For information concerning other installation require-

ments and/or component modifications, consult TUSONIX Customer Engineering at (520) 744-0400.

General Recommendations

Handling: Excessive force or direct impact to the component may result in breakage. Lead bending or cutting,

if necessary, should be done with a support for the lead to prevent mechanical stress to the

component. Components with required lead modifications are available from TUSONIX.

Lead Soldering: Use a temperature controlled soldering iron with SN60 or SN63 RMA Flux core wire. Maximum

soldering temperature to be 500°F(260°C) with a dwell time of 3 seconds maximum. The use of a

heat sink between the component body and the solder joint is highly recommended.

Flux Removal: Optimum flux removal can be achieved by vapor degreasing the components immediately after the

soldering operation. Total immersion of the components is not recommended.

Solder Mount Recommendations

Mounting: Use a convection or infrared oven and SN60 or SN63 solder paste, or solder preforms, with RMA

Flux. The oven profile should slowly heat the entire assembly to a reflow temperature of 430°F

(221°C), with a rate of change not to exceed 5°F,3°C/Sec. and a dwell time as short as possible.

Internal Use a temperature controlled soldering iron with SN62 silver bearing (2%) RMA Flux core solder

Electrode wire. The components should be preheated to 300°F (150°C), then soldered with a maximum

Soldering: temperature of 500°F (260°C) and a dwell of 3 seconds maximum.

Bushing Mount Recommendations

For Mounting Torque, please see standard hardware dimensions table on page 24.

EIA/Tusonix Tolerance Codes

TEMPERATURE

CHARACTERISTICS

CAPACITANCE

TOLERANCE

EIA Code Temperature Range

+10°C to +85°C

-30°C to +85°C

-55°C to +85°C

-55°C to +125°C

± 3.3%

± 4.7%

± 7.5%

± 10%

± 15%

± 22%

+ 22% -33%

+ 22% -56%

+ 22% -82%

+ 22% -90%

EIA Code Maximum Cap. Change

Nominal

Capacitnce

10 pF or

Less

Code

Nominal

Capacitnce

over 10 pF

GMV◆

± 0.1 pF

± 0.25 pF

± 0.5 pF

± 0.3 pF

± 1 pF

± 2 pF

± 3%

± 5%

± 10%

± 2%

GMV◆

+50% -20%

± 0.10%

± 0.25%

± 0.50%

+70% -30%

± 1%

± 2%

± 3%

+60% -40%

± 5%

± 10%

+100% -40%

CAPACITANCE

TOLERANCE (Cont.)

Nominal

Capacitnce

10 pF or

Less

Code

Nominal

Capacitnce

over 10 pF

± 20%

± 0.4 pF

± 0.2 pF

MAX.

± 20%

± 30%

+100% -0%

± 15%

± 2.5%

+50% -15%

+30% -20%

+80% -0%

± 7%

+50% -30%

+40% -10%

+50% -0%

+80% -20%

◆GMV: TUSONIX Code: Guarantied Minimum Value

Please note: Maximum Capacitance for each part

number is determined by the required operating

temperature range and maximum capacitance

change.

7741 North Business Park Drive

Tucson, Arizona 85743

Ph: 520-744-0400 Fax: 520-744-6155

Web site: www.tusonix.com E-mail: sales@tusonix.com

General Test Specifications

The Components shown in this catalog have been designed and subjected to the following test

plan, as is applicable for the individual components. The information shown can be used as a

basis for component specifications. For additional information, please consult Customer Engi-

neering at (520) 744-0400.

Filters governed by MIL-PRF-15733 shall be inspected and tested to the requirements of the

specification and the applicable specification (slash) sheet.

PERIODIC QUALITY CONFORMANCE INSPECTION:

A periodic quality conformance inspection program consisting of environmental and reliability

testing is in place to ensure that product integrity is consistently maintained.

TUSONIX on-line www.tusonix.com

The TUSONIX Web site provides visitors with a wide range of product and ordering information.

At www.tusonix.com, customers can view product information and download catalogs in Adobe

Acrobat

.pdf format. Customers can also view or link to Sales Offices, International Agents and

Distributors. An on-line request form allows customers to immediately specify product require-

ments and request product information.

LOT ACCEPTANCE INSPECTION:

INSPECTION OR TEST

TEST METHOD PER MIL-STD-202

EXCEPT AS NOTED

POST TEST REQUIREMENTS

Visual and Mechanical

Materials, Design, Construction

and Workmanship

Physical Dimensions & Marking

Seal (4601 Style Only)

Capacitance

Dissipation Factor (1/Q)

Dielectric Withstanding Voltage

Insulation Resistance

Insertion Loss

DC Resistance (4601 Style Only)

Solderability (5pcs)

In accordance with applicable

requirements

Method 301, 2 seconds, 50 mA max. surge

current, 2 times WVDC.

Method 112, condition A

Method 305, 1KHz, 1±0.2 VRMS max. +25°C

Method 306, 1KHz, 1±0.2 VRMS max. +25°C

Method 302, 50 mA max. charging current,

100VDC, 2 minutes or as specified by

individual variation

MIL-STD-220, 50 Ohms, +25°C, no load

MIL-PRF-15733

Method 208

No leaks

Within specified tolerance

4.0% max

Greater than 10,000 Megohms

or 100 Ohm-Farads, whichever

is less.

Per application requirements.

0.01 Ohms max.

Per applicable requirements.

No evidence of damage or

break down.

P1-P3 P4-P6 P7-P9 P10-P12 P13-P14

4400-900

Mfr. #:

Buy 4400-900

Manufacturer:

Description:

EMI Kits Kit consists of 5 pieces of 10 P/N's.

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

4400-900

4400-900

Products related to this Datasheet