OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

BFC233610223

P1-P3P4-P6P7-P9P10-P11
MKP336 1 X1
www.vishay.com
Vishay BCcomponents
Not Recommended for New Designs, Use MKP338 1 X1
Revision: 21-Sep-16
7
Document Number: 28117
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SUB-GROUP C1A PART OF SAMPLE
OF SUB-GROUP C1
D
4.4 Resistance to soldering heat No pre-drying
Method: 1A
Solder bath: 260 °C
Duration: 10 s
4.19 Component solvent resistance Isopropylalcohol at room temperature
Method: 2
Immersion time: 5 min ± 0.5 min
Recovery time:
Min. 1 h, max. 2 h
4.4.2 Final measurements Visual examination No visible damage
Legible marking
Capacitance |C/C| 5 % of the value measured
initially
Tangent of loss angle Increase of tan : 0.008
Compared to values measured initially
Insulation resistance As specified in section “Insulation
Resistance” of this specification
SUB-GROUP C1B PART OF SAMPLE
OF SUB-GROUP C1
D
Initial measurements Capacitance
Tangent of loss angle:
For C 470 nF at 100 kHz
For C > 470 nF at 10 kHz
No visible damage
Legible marking
4.20 Solvent resistance of the marking:
see section “General Notes”; item 5
Isopropylalcohol at room temperature
Method: 1
Rubbing material: cotton wool
Immersion time: 5 min ± 0.5 min
No visible damage
4.6 Rapid change of temperature A = - 55 °C
B = + 105 °C
5 cycles
SUB-GROUP C1B PART OF SAMPLE
OF SUB-GROUP C1
D
4.6.1 Inspection Duration t = 30 min
4.7 Vibration (see note 3.1) Visual examination
Mounting: see section “Mounting” of this
specification
Procedure B4:
Frequency range: 10 Hz to 55 Hz
Amplitude: 0.75 mm or
Acceleration 98 m/s
(whichever is less severe)
Total duration 6 h
No visible damage
4.7.2 Final inspection Visual examination No visible damage
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER
AND TEST
D
OR
ND
CONDITIONS PERFORMANCE REQUIREMENTS
MKP336 1 X1
www.vishay.com
Vishay BCcomponents
Not Recommended for New Designs, Use MKP338 1 X1
Revision: 21-Sep-16
8
Document Number: 28117
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SUB-GROUP C1B PART OF SAMPLE
OF SUB-GROUP C1
D
4.9 Shock (see note 3) Mounting: See section “Mounting” for
more information
Pulse shape: Half sine
Acceleration: 490 m/s
Duration of pulse: 11 ms
4.9.2 Final measurements Visual examination No visible damage
Capacitance |C/C| 5 % of the value measured
initially
Tangent of loss angle Increase of tan : 0.008
Compared to values measured initially
Insulation resistance As specified in section “Insulation
Resistance” of this specification
SUB-GROUP C1 COMBINED SAMPLE
OF SPECIMENS OF
SUB-GROUPS C1A AND C1B
D
4.11 Climatic sequence
4.11.1 Initial measurements Capacitance
Measured in 4.4.2 and 4.9.2
Tangent of loss angle:
Measured initially in C1A and C1B
4.11.2 Dry heat Temperature: 105 °C
Duration: 16 h
4.11.3 Damp heat cyclic
Test Db
First cycle
4.11.4 Cold Temperature: - 55 °C
Duration: 2 h
4.11.5 Damp heat cyclic
Test Db
remaining cycles
SUB-GROUP C1 COMBINED SAMPLE
OF SPECIMENS OF
SUB-GROUPS C1A AND C1B
D
4.11.6 Final measurements Visual examination No visible damage
Legible marking
Capacitance |C/C| 5 % of the value measured in
4.11.1.
Tangent of loss angle Increase of tan : 0.008 compared to
values measured in 4.11.1
Voltage proof
1200 V
DC
; 1 min between term
No permanent breakdown or flash-over
Insulation resistance 50 % of values specified in section
“Insulation Resistance” of this
specification
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER
AND TEST
D
OR
ND
CONDITIONS PERFORMANCE REQUIREMENTS
MKP336 1 X1
www.vishay.com
Vishay BCcomponents
Not Recommended for New Designs, Use MKP338 1 X1
Revision: 21-Sep-16
9
Document Number: 28117
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SUB-GROUP C2 D
4.12 Damp heat steady state 56 days, 40 °C, 90 % to 95 % RH,
no load capacitance
4.12.1 Initial measurements Tangent of loss angle at 10 kHz
4.12.3 Final measurements Visual examination No visible damage
Legible marking
Capacitance |C/C| 5 % of the value measured in
4.12.1.
Tangent of loss angle Increase of tan : 0.008
Compared to values measured in 4.12.1.
Voltage proof
1200 V
DC
; 1 min between term
No permanent breakdown or flash-over
Insulation resistance 50 % of values specified in section
“Insulation Resistance” of this
specification
SUB GROUP C3 D
4.13.1 Initial measurements Capacitance
Tangent of loss angle:
For C 470 nF at 100 kHz
For C > 470 nF at 10 kHz
4.13 Impulse voltage 3 successive impulses, full wave, peak
voltage:
X1: 4 kV
Max. 24 pulses
No selfhealing breakdowns or flashover
4.14 Endurance Duration: 1000 h
1.25 U
RAC
at 105 °C
Once in every hour the voltage is
increased to 1000 V
RMS
for 0.1 s via
resistor of 47 ± 5 %
SUB GROUP C3 D
4.14.7 Final measurements Visual examination No visible damage
Legible marking
Capacitance |C/C| 10 % compared to values
measured in 4.13.1.
Tangent of loss angle Increase of tan : 0.008
Compared to values measured in 4.13.1.
Voltage proof
1200 V
DC
; 1 min between terminations
2050 V
DC
; 1 min between terminations
and case
No permanent breakdown or flash-over
Insulation resistance 50 % of values specified in section
“Insulation Resistance” of this
specification
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER
AND TEST
D
OR
ND
CONDITIONS PERFORMANCE REQUIREMENTS
P1-P3P4-P6P7-P9P10-P11

BFC233610223

Mfr. #:
Buy BFC233610223
Manufacturer:
Vishay
Description:
Film Capacitors .022uF 20% 275volts SUPRES FILM CAP
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet