Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
Surface Mount
NPCAP
TM
-PXHSeries
・
Super low ESR, impedance and high heat resistance have been obtained by using con-
ductive polymer as electrolyte.
・
Suitable for DC-DC converters, voltage regulators and decoupling applications.
・
Endurance : 125
℃
1,000 hours
・
Rated voltage range : 2.5 to 20V
dc
, Capacitance range : 22 to 1,000μF
・
Case size range :
φ
6.3×5.7L to
φ
10×7.7L
・
Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
・
RoHS2 Compliant
・
Halogen Free
◆
SPECIFICATIONS
Items Characteristics
Category
Temperature Range
-55 to +125
℃
Rated Voltage Range
2.5 to 20V
dc
Capacitance Tolerance
±
20% (M) (at 20
℃
, 120Hz)
Surge Voltage
Rated voltage
×
1.15 (at 125
℃
)
Leakage Current
Shall not exceed values shown in STANDARD RATINGS. (at 20
℃
after 2 minutes)
Dissipation Factor
(tan
δ
)
0.12 max.
(at 20
℃
, 120Hz)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Z(-25
℃
)/Z(+20
℃
)
≦
1.15
Z(-55
℃
)/Z(+20
℃
)
≦
1.25
(at 100kHz)
Endurance
The following specifications shall be satisfied when the capacitors are restored to 20
℃
after the rated voltage is applied for 1,000 hours
at 125
℃
.
Appearance No significant damage
Capacitance change
≦±
20% of the initial value
D.F. (tan
δ
)
≦
200% of the initial specified value
ESR
≦
200% of the initial specified value
Leakage current
≦
The initial specified value
Bias Humidity
The following specifications shall be satisfied when the capacitors are restored to 20
℃
after subjecting them to the DC rated voltage at
60
℃
, 90 to 95% RH for 1,000 hours.
Appearance No significant damage
Capacitance change
≦±
20% of the initial value
D.F. (tan
δ
)
≦
150% of the initial specified value
ESR
≦
150% of the initial specified value
Leakage current
≦
The initial specified value
Surge Voltage
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 125
℃
for 30 seconds
through a protective resistor(R=1k
Ω
) and discharge for 5 minutes 30 seconds.
Appearance No significant damage
Capacitance change
≦±
20% of the initial value
D.F. (tan
δ
)
≦
150% of the initial specified value
ESR
≦
150% of the initial specified value
Leakage current
≦
The initial specified value
Failure Rate
0.5% per 1,000 hours maximum (Confidence level 60% at 125
℃
)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 125℃.
◆
DIMENSIONS [mm]
0.3max.
W
C
±
0.2
B
±
0.2
P
Size code
F60
H70
J80
φD
6.3
8
10
L
5.7
6.7
7.7
A
6.6
8.3
10.3
B
6.6
8.3
10.3
C
7.2
9.0
11.0
W
0.5 to 0.8
0.7 to 1.1
0.7 to 1.1
P
1.9
3.1
4.5
Terminal Code : A
●
A
±
0.2
◆
PART NUMBERING SYSTEM
Please refer to "Product code guide (conductive polymer type)"
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 22µF:220,100µF:101)
Taping code
Terminal code
Voltage code (ex. 6.3V:6R3,10V:100)
Series code
Category
A P X H A R A GM
1 3 42 6 789 10 13125 18171611 1514
Higher temperature
PXH
PXA P2-28
◆
MARKING
H
39F
22
20
V
2-32
CAT. No. E1001R
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
