OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

AD713JNZ

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21
AD713
Rev. F | Page 3 of 20
SPECIFICATIONS
V
S
= ±15 V at T
A
= 25°C, unless otherwise noted.
Table 1.
AD713J/AD713A
Parameter Test Conditions/Comments Min Typ Max Unit
INPUT OFFSET VOLTAGE
1
Initial Offset 0.3 1.5 mV
Offset T
MIN
to T
MAX
0.5 2 mV
vs. Temp 5 μV/°C
vs. Supply 78 95 dB
T
MIN
to T
MAX
76 95 dB
Long-Term Stability 15 μV/Month
INPUT BIAS CURRENT
2
V
CM
= 0 V 40 150 pA
V
CM
= 0 V at T
MAX
3.4/9.6 nA
V
CM
= ±10 V 55 200 pA
INPUT OFFSET CURRENT V
CM
= 0 V 10 75 pA
V
CM
= 0 V at T
MAX
1.7/4.8 pA
MATCHING CHARACTERISTICS
Input Offset Voltage 0.5 1.8 mV
T
MIN
to T
MAX
0.7 2.3 mV
Input Offset Voltage Drift 8 μV/°C
Input Bias Current 10 100 pA
Crosstalk f = 1 kHz −130 dB
f = 100 kHz −95 dB
FREQUENCY RESPONSE
Small Signal Bandwidth G = −1 3.0 4.0 MHz
Full Power Response V
O
= 20 V p-p 200 kHz
Slew Rate G = −1 16 20 V/μs
Settling Time to 0.01% 1.0 1.2 μs
Total Harmonic Distortion f = 1 kHz; R
L
≥ 2 kΩ; V
O
= 3 V rms 0.0003 %
INPUT IMPEDANCE
Differential
3
3 × 10
12
||5.5 Ω||pF
Common Mode
4
3 × 10
12
||5.5 Ω||pF
INPUT VOLTAGE RANGE
Differential ±20 V
Common-Mode Voltage +14.5/−11.5 V
T
MIN
to T
MAX
−11 +13 V
Common Mode V
CM
= ±10 V 78 88 dB
Rejection Ratio T
MIN
to T
MAX
76 84 dB
V
CM
= ±11 V 72 84 dB
T
MIN
to T
MAX
70 80 dB
INPUT VOLTAGE NOISE 0.1 Hz to 10 Hz 2 μV p-p
f = 10 Hz 45 nV/√Hz
f = 100 Hz 22 nV/√Hz
f = 1 kHz 18 nV/√Hz
f = 10 kHz 16 nV/√Hz
INPUT CURRENT NOISE f = 1 kHz 0.01 pA/√Hz
OPEN-LOOP GAIN V
O
= ±10 V; R
L
≥ 2 kΩ 150 400 V/mV
T
MIN
to T
MAX
100 V/mV
AD713
Rev. F | Page 4 of 20
AD713J/AD713A
Parameter Test Conditions/Comments Min Typ Max Unit
OUTPUT CHARACTERISTICS
Voltage R
L
≥ 2 kΩ +13/−12.5 +13.9/−13.3 V
T
MIN
to T
MAX
±12 +13.8/−13.1 V
Current Short circuit 25 mA
POWER SUPPLY
Rated Performance ±15 V
Operating Range ±4.5 ±18 V
Quiescent Current 10.0 13.5 mA
TRANSISTOR COUNT Number of transistors 120
1
Input offset voltage specifications are guaranteed after 5 minutes of operation at T
A
= 25°C.
2
Bias current specifications are guaranteed maximum at either input after 5 minutes of operation at T
A
= 25°C. For higher temperatures, the current doubles every 10°C.
3
Defined as the voltage between inputs, such that neither exceeds ±10 V from ground.
4
Typically exceeding −14.1 V negative common-mode voltage on either input results in an output phase reversal.
AD713
Rev. F | Page 5 of 20
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter Rating
Supply Voltage ±18 V
Input Voltage
1
±18 V
Output Short-Circuit Duration
(For One Amplifier) Indefinite
Differential Input Voltage +V
S
and −V
S
Storage Temperature Range (Q) −65°C to +150°C
Storage Temperature Range (N, R) −65°C to +125°C
Operating Temperature Range
AD713J 0°C to 70°C
AD713A −40°C to +85°C
Lead Temperature Range (Soldering, 60 sec) 300°C
1
For supply voltages less than ±18 V, the absolute maximum input voltage is
equal to the supply voltage.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL RESISTANCE
θ
JA
is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 3. Thermal Resistance
Package Type θ
JA
θ
JC
Unit
14-Lead PDIP (N-14) 100 30 °C/W
14-Lead CERDIP (Q-14) 110 30 °C/W
16-Lead SOIC_W (RW-16) 100 30 °C/W
ESD CAUTION
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21

AD713JNZ

Mfr. #:
Buy AD713JNZ
Manufacturer:
Analog Devices Inc.
Description:
Precision Amplifiers PREC HIGH Spd QUAD BIFET
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet