LT6013/LT6014
8
60134fb
TYPICAL PERFOR A CE CHARACTERISTICS
UW
Distribution of Input Offset Voltage
Input Offset Voltage
vs Temperature
Offset Voltage
vs Input Common Mode Voltage
Input Bias Current vs Temperature
Input Bias Current
vs Input Common Mode Voltage
–25
INPUT OFFSET VOLTAGE (µV)
0
PERCENT OF UNITS (%)
5
15
20
25
60134 G01
10
30
V
S
= 5V, 0V
T
A
= 25°C
LT6013AS8
–45 –35 –15 –5 5 15 25 35 45
TEMPERATURE (°C)
–50
–125
OFFSET VOLTAGE (µV)
–100
–50
–25
0
125
50
0
50
75
60134 G02
–75
75
100
25
–25
25
100
125
V
S
= 5V, 0V
REPRESENTATIVE UNITS
INPUT COMMON MODE VOLTAGE (V)
1000
900
800
600
400
200
700
500
300
100
0
60134 G03
CHANGE IN OFFSET VOLTAGE (µV)
V
S
= 5V, 0V
T
A
= 85°C
T
A
= –40°C
T
A
= 25°C
0
0.5
1.0 1.5 2.0 2.5 3.0 3.5 4.0 5.04.5
TEMPERATURE (°C)
–50
–800
INPUT BIAS CURRENT (pA)
–600
–200
0
50
800
60134 G05
–400
0
–25
75 100
25 125
200
400
600
V
S
= 5V, 0V
TYPICAL PART
INPUT COMMON MODE VOLTAGE (V)
0
–400
–300
–200
CHANGE IN INPUT BIAS CURRENT (pA)
–100
0
100
200
400
300
0.5
1.0 1.5 2.0
60134 G06
2.5 3.0 3.5 4.0 4.5
V
S
= 5V, 0V
T
A
= 85°C
T
A
= 25°C
T
A
= –40°C
INPUT BIAS CURRENT (pA)
–175
0
PERCENT OF UNITS (%)
5
15
30
35
20
25
–75 25–25
60134 G04
10
–125 75 125 175
LT6013AS8
Distribution of Input Bias Current
ELECTRICAL CHARACTERISTICS
Note 1: Absolute Maximum Ratings are those beyond which the life of the
device may be impaired.
Note 2: The inputs are protected by back-to-back diodes and internal
series resistors. If the differential input voltage exceeds 10V, the input
current must be limited to less than 10mA.
Note 3: A heat sink may be required to keep the junction temperature
below absolute maximum ratings.
Note 4: The LT6013C/LT6014C and LT6013I/LT6014I are guaranteed
functional over the operating temperature range of – 40°C to 85°C.
Note 5: The LT6013C and LT6014C are guaranteed to meet the specified
performance from 0°C to 70°C and are designed, characterized and
expected to meet specified performance from –40°C to 85°C but is not
tested or QA sampled at these temperatures. The LT6013I and LT6014I are
guaranteed to meet specified performance from –40°C to 85°C.
Note 6: This parameter is not 100% tested.
Note 7: Matching parameters are the difference between the two
amplifiers. ∆CMRR and ∆PSRR are defined as follows: (1) CMRR and
PSRR are measured in µV/V for the individual amplifiers. (2) The
difference between matching amplifiers is calculated in µV/V. (3) The
result is converted to dB.
Note 8: The specifications for V
OS
, I
B
, and I
OS
depend on the grade and on
the package. The following table clarifies the notations.
STANDARD GRADE A GRADE
S8 Package LT6013S8, LT6014S8 LT6013AS8, LT6014AS8
DFN Package LT6013DD, LT6014DD LT6013ADD, LT6014ADD