4
FN6090.2
July 28, 2006
POWER SUPPLY CHARACTERISTICS
Power Supply Range Full 1.65 3.6 V
Positive Supply Current, I+ V+ = +1.65 to 3.6V, V
IN
= 0V or V+ 25 - - 40 nA
Full - - 750 nA
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V
INL
Full - - 0.5 V
Input Voltage High, V
INH
Full 1.4 - - V
Input Current, I
INH
, I
INL
V+ = 3.3V, V
IN
= 0V or V+ (Note 8) Full -0.5 - 0.5 A
NOTES:
4. V
IN
= input voltage to perform proper function.
5. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
6. Parts are 100% tested at +25°C. Limits across the full temperature range are guaranteed by design and correlation.
7. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range.
8. Guaranteed but not tested.
9. R
ON
matching between channels is calculated by subtracting the channel with the highest max Ron value from the channel with lowest max Ron
value.
Electrical Specifications - 1.8V Supply Test Conditions: V+ = +1.65V to +2V, GND = 0V, V
INH
= 1.0V, V
INL
= 0.4V (Note 4, 6),
Unless Otherwise Specified
PARAMETER TEST CONDITIONS
TEMP
(°C)
(NOTE 5)
MIN TYP
(NOTE 5)
MAX UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
Full 0 - V+ V
ON Resistance, R
ON
V+ = 1.8V, I
COM
= 100mA, V
NO
or V
NC
= 0V to V+,
See Figure 5, Note 8
25 - 0.4 0.6
Full - - 0.6
NO or NC OFF Leakage Current,
I
NO(OFF)
or I
NC(OFF)
V+ = 2.0V, V
COM
= 0.3V, 1.8V, V
NO
or V
NC
= 1.8V, 0.3V 25 -2 - 2 nA
Full -40 - 40 nA
COM ON Leakage Current,
I
COM(ON)
V = 2.0V, V
COM
= 0.3V, 1.8V, or V
NO
or V
NC
= 0.3V,
1.8V
25 -3 - 3 nA
Full -60 - 60 nA
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
V+ = 1.65V, V
NO
or V
NC
= 1.0V, R
L
=50, C
L
= 35pF,
See Figure 1, Note 8
25 - 22 28 ns
Full - - 33 ns
Turn-OFF Time, t
OFF
V+ = 1.65V, V
NO
or V
NC
= 1.0V, R
L
=50, C
L
= 35pF,
See Figure 1, Note 8
25 - 9 15 ns
Full - - 20 ns
Break-Before-Make Time Delay, t
D
V+ = 2.0V, V
NO
or V
NC
= 1.0V, R
L
=50, C
L
= 35pF,
See Figure 3, Note 8
Full 2 9 - ns
Charge Injection, Q C
L
= 1.0nF, V
G
= 0V, R
G
= 0See Figure 2 25 - 49 - pC
OFF Isolation R
L
= 50, C
L
= 5pF, f = 100kHz, V
COM
= 1V
RMS
,
See Figure 4
25 - 68 - dB
Crosstalk (Channel-to-Channel) R
L
= 50, C
L
= 5pF, f = 100kHz, V
COM
= 1V
RMS
,
See Figure 6
25 - -95 - dB
NO or NC OFF Capacitance, C
OFF
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, See Figure 7 25 - 115 - pF
COM ON Capacitance, C
COM(ON)
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, See Figure 7 25 - 224 - pF
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V
INL
Full - - 0.4 V
Input Voltage High, V
INH
Full 1.0 - - V
Input Current, I
INH
, I
INL
V+ = 2.0V, V
IN
= 0V or V+ (Note 8) Full -0.5 - 0.5 A
Electrical Specifications - 3V Supply Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, V
INH
= 1.4V, V
INL
= 0.5V (Note 4, 6),
Unless Otherwise Specified (Continued)
PARAMETER TEST CONDITIONS
TEMP
(°C)
(NOTE 5)
MIN TYP
(NOTE 5)
MAX UNITS
ISL43L410
