DO NOT
SCALE FROM
THIS PRINT
.025
REF
0.64
(SEE NOTE 8)
.047
REF
1.19
(TYP)
.155 3.94
.480 12.19
REF
.285 7.24
REF
.165
(TYP)
4.19
((No OF POS - 1) x .165[4.19])
.008[.20]
2
MAX SWAY
(EITHER DIRECTION)
"A"
"A"
IPBS-108-X1-XX-S SHOWN
FIG. 1
IPBS-XX-S
C
C
C
C
.213 5.41
REF
((No OF POS x .165[4.19]) +.080[2.03]) REF
((No OF POS -1) x .165[4.19]) REF
.123
REF
3.11
01
02
.080
-
.015
+
.005
(TYP)
2.03
-
0.38
+
0.13
.023
REF
0.59
2.5
MAX SWAY
(EITHER DIRECTION)
SECTION "A"-"A"
C-168-01-XX-X
C
C
IPBS-1XX-XX-XX-S-XX
No OF POSITIONS
-02 THRU -10
(PER ROW)
ROW SPECIFICATION
-S: SINGLE (USE IPBS-XX-S)
PLATING SPECIFICATION
-T: TIN (USE C-168-XX-XX-T)
-TM: MATTE TIN (USE C-168-XX-XX-T)
LEAD STYLE
-01: STANDARD POWER, THROUGH HOLE
(USE C-168-01-SP-XX)(SEE FIG. 1)
-02: STANDARD POWER, SURFACE MOUNT
(USE C-168-02-SP-XX)(SEE FIG. 2, SHEET 2)
-H1: HIGH POWER, THROUGH HOLE
(USE C-168-01-HP-XX)(SEE FIG. 1)(SEE NOTE 9)
-H2: HIGH POWER, SURFACE MOUNT
(USE C-168-02-HP-XX)(SEE FIG. 2, SHEET 2) (SEE NOTE 9)
OPTION
-GP: GUIDE POSTS
(USE IPBS-XX-S-GP)
[SEE FIG. 3, SHT 2]
PACKAGING VIEWS
-01, -H1
-02, -H2
-01-GP, -H2-GP
C
NOTE: PARTS TO BE LOADED WITH POSITION #1
IN SAME DIRECTION AS ARROW ON TUBE
E
SHEET OF
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS ANGLES
.XX:
.01 [.3] 2
.XXX:
.005 [.13]
.XXXX:
.0020 [.051]
MATERIAL:
.165[4.19] SINGLE ROW SOCKET ASSEMBLY
BY:
IPBS-1XX-XX-XX-S-XX
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
DEAN P
5/12/2003
2
1
SHEET SCALE: 2:1
INSULATOR: LCP, COLOR: BLACK
CONTACT: PHOS BRONZE (-SP) or
HIGH COPPER ALLOY (-HP)
F:\DWG\MISC\MKTG\IPBS-1XX-XX-XX-S-XX-MKT.SLDDRW
NOTES:
1. REPRESENTS A CRITICAL DIMENSION.
2. COPLANARITY (FOR -X2): SEE TABLE 1.
3. BURR ALLOWANCE: .003[.08] MAX.
4. PARTS TO BE MOLDED TO POSITION.
5. MINIMUM PUSHOUT FORCE: 1 LB[4.45 N].
6. MEASURED AT THE LOWEST POINT.
7. ALL PIN TO PIN DIMENSIONS TO BE MEASURED
FROM TIP TO TIP.
8. TWO POSITION PART WILL HAVE STANDOFFS ON ENDS.
9. AVAILABLE TO EXISTING CUSTOMERS ONLY. DO NOT DESIGN
IN AS OF REVISION D.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
REVISION E
