BNX003-01 Datasheet BNX003-01 | P1-P3

Spec. No. JENF243H-0005H-01 P 1/ 7

MURATA MFG CO.,LTD.

Reference

Only

1. Scope

This reference specification applies to Block Type EMIFIL

2. Rating

2.1 Customer Part Number

2.2 Murata Part Number BNX003-01

2.3 Rated Voltage 150 V(DC)

2.4 Test Voltage 375 V(DC)

2.5 Rated Current 10 A(DC)

2.6 Insulation Resistance 100 M min.

2.7 Voltage Drop 30 mV max.

2.8 Insertion Loss

5 MHz to 1 GHz : 40dB min.

Line impedance = 50 

2.9 Equivalent Circuits See the item 4

2.10 Operating Temperature - 30 °C ~ + 85 °C

2.11 Storage Temperature - 40 °C ~ + 85 °C

3. Standard Testing Condition

Temperature : Ordinary Temp. 15 °C to 35 °C Temperature : 20 °C ± 2 °C

Humidity : Ordinary Humidity 25 %(RH) to 85 %(RH) Humidity : 60 %(RH) to 70 %(RH)

Atmospheric pressure : 86 kPa to 106 kPa

4. Style and Dimensions

Note) Although some part of the product surface seems to be white in some cases, do not care because it is the

result of waxing process for humidity resistance improvement. This wax does not make bad affection to mechanical

or electrical performance, reliability of the product.

TERMINAL LAYOUT (BOTTOM FIGURE)  DIMENSIONS OF INSTALLATION HOLES

(front view)

Block Type EMIFIL® BNX003-01

Reference

Specification

PSG

(4)

(3)

(1)

(2)



0.8

0.6

±0.1

11.0±0.5

7.5±0.2

12.0±0.5

18.0 max.

5.0±0.5

3.5±1.0

13.0 max.



0.8

±0.1

2.5

±0.2

2.5

±0.2

2.5

±0.2

2.5

±0.2



0.8

(in mm)

7.5±0.1

5.0±0.1

2.5±0.1

(CG)

(CB)

(CG)

(B)

(CG)

(PSG)

2.5±0.1



1.2

(in mm)

Spec. No. JENF243H-0005H-01 P 2/ 7

MURATA MFG CO.,LTD.

Reference

Only

 EQUIVALENT CIRCUIT

 Unit Mass (Typical value)

3.2g

5. Marking

Filter shall be marked as follows.

6. Electrical Performance

No. Item Specification Test Method

6.1 Insulation

Resistance

Meet item 2.6. Measured at DC rated voltage between terminal

(1)(2) and (3)(4).

Time : 1 minute

Suitable resistor : 1M.

6.2 Dielectric

Strength

Filter shall be no failure. Test voltage shall be applied between terminal

(1)(2) and terminal (3)(4).

Time : 1 to 5 seconds.

Charging current : 50 mA max.

6.3 Voltage

Drop

Meet item 2.7. Rated Current : 10 A

6.4 Insertion

Loss

Meet item 2.8.

Insertion Loss = 20log (E

/ E

)

Ｅ

: Level without FILTER (short)

Ｅ

１

: Level with FILTER

7. Mechanical Performance

No. Item Specification Test Method

7.1 Appearance and

Dimensions

Meet item 4. Visual Inspection and measured with Slide

Calipers.

7.2 Marking Marking is able to be read easily. It is inspected Visually.

PSG

(1)

(2)

(4)

(3)

(1) ~ (4) : Terminal

Specimen

(1)

(2)

(3)

(4)



10dB



Method of measurement based on MIL- STD- 220

～



10dB

Attenuator

Balun

Specimen

Attenuator

(1)

(2)

(3)

(4)

BNX003-01

Murata mark

Part Number

Manufacturing Date

(Ex.) 59

･･･

1995 (Last digit of the year)

･･･

September

Jan. to Sept. 1 ~ 9

Oct.:O,Nov.:N,Dec,:D

Spec. No. JENF243H-0005H-01 P 3/ 7

MURATA MFG CO.,LTD.

Reference

Only

No. Item Specification Test Method

7.3 Vibration Meet Table 1.

Table 1

It shall be soldered on the substrate.

Range of Vibration Frequency :

10 to 2000 to 10Hz for 20 minutes

Testing Time : A period of 2 hours in each of 3

Mutually perpendicular directions

(Total 6 hours)

Double Amplitude : 1.5mm or acceleration 196m /

Then measured after exposure in the room

condition for 4 to 24 hours.

7.4 Solderability Then the lead is covered with a

continuous new solder coating at

least 75% along the circumference

of the immersed part.

Flux : Ethanol solution of rosin, 25(wt)%

Pre-heat : 150 ± 10 °C, 60 ~ 90 s

Solder : Sn-3.0Ag-0.5Cu

Solder Temperature 245 ± 5 °C

Immersion Time : 2 ± 0.5 seconds

7.5 Resistance to

soldering heat

Meet Table 1.

Flux : Ethanol solution of rosin, 25(wt)%

Pre-heat : 150 ± 10 °C, 60 ~ 90 s

Solder : Sn-3.0Ag-0.5Cu

Solder Temperature : 270 ± 10 °C

Immersion Time : 10s (+ 2s , - 0s)

Then measure values after exposure in the room

condition for 24 to 48 hours.

7.6 Resistance to

soldering iron

Solder : Sn-3.0Ag-0.5Cu

Tip Temperature : 350 ± 10 °C

Time : 4 ± 1 s

Then measure values after exposure in the room

condition for 24 to 48 hours.

8. Environmental Performance

No. Item Specification Test Method

8.1 Temperature

Cycle

Meet Table 1.

1 Cycle

1 step : - 30 °C (+ 0°C , - 3°C) / 30 minutes

2 step : Room Temperature / within 5 minutes.

3 step : + 85 °C (+ 3°C , - 0°C) / 30 minutes

4 step : Room Temperature / within 5 minutes.

Total of 10 cycle

Then measured after exposure in the room

condition for 24 to 48 hours.

8.2 Humidity Life

Temperature : 40 ± 2 °C

Humidity : 95 %(RH)

Rated Voltage : 150 V(DC)

Time : 500 h (+ 24h , - 0h)

Then measured after exposure in the room

condition for 4 to 24 hours.

8.3 Heat Life

Temperature : 85 ± 2 °C

Voltage : Rated Voltage  2

Time : 1000 h (+ 48h , - 0h)

Then measured after exposure in the room

condition for 24 to 48 hours.

Appearance No damaged

Insulation

Resistance

30 M min.

Dielectric

Strength

No failure

Insertion

Loss

Meet item 2.8

1.6±0.8mm

Molten Solder

P1-P3 P4-P6 P7-P7

BNX003-01

Mfr. #:

Buy BNX003-01

Manufacturer:

Description:

EMI Network Filter 150V 10A

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet

BNX003-01