5
Absolute Maximum Ratings Thermal Information
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to15V
Input Voltages
IN (Note 3). . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
NO, NC (Note 3) . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Output Voltages
COM (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 10mA
Peak Current, IN, NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . . 20mA
ESD Rating (Per MIL-STD-883 Method 3015). . . . . . . . . . . . . .>2kV
Operating Conditions
Temperature Range
ISL8454XCX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
o
C to 70
o
C
ISL8454XIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40
o
C to 85
o
C
Thermal Resistance (Typical, Note 4)
JA
(
o
C/W)
6 Ld SOT-23 Package . . . . . . . . . . . . . . . . . . . . . . . 230
8 Ld SOT-23 Package . . . . . . . . . . . . . . . . . . . . . . . 215
8 Ld MSOP Package . . . . . . . . . . . . . . . . . . . . . . . . 210
8 LD SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . 170
8 LD PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . 140
Maximum Junction Temperature (Plastic Package). . . . . . . . 150
o
C
Moisture Sensitivity (See Technical Brief TB363)
All Other Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level 1
8 Ld SOT-23 Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level 2
Maximum Storage Temperature Range . . . . . . . . . . . . -65
o
C to 150
o
C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300
o
C
(SOIC, MSOP and SOT-23 - Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
3. Signals on NC, NO, COM, or IN exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings.
4.
JA
is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications - 5V Supply Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, V
INH
= 2.4V, V
INL
= 0.8V (Note 5),
Unless Otherwise Specified
PARAMETER TEST CONDITIONS
TEMP
(
o
C)
MIN
(NOTE 6) TYP
MAX
(NOTE 6) UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
Full 0 - V+ V
ON Resistance, R
ON
V+ = 4.5V, I
COM
= 1.0mA, V
NO
or V
NC
= 3.5V,
See Figure 5
25 - 30 60
Full - - 75
R
ON
Matching Between Channels,
R
ON
V+ = 5V, I
COM
= 1.0mA, V
NO
or V
NC
= 3.5V 25 - 0.8 2
Full - - 4
R
ON
Flatness, R
FLAT(ON)
V+ = 5V, I
COM
= 1.0mA, V
NO
or V
NC
= 1V, 2V, 3V Full - 7 8
NO or NC OFF Leakage Current,
I
NO(OFF)
or I
NC(OFF)
V+ = 5.5V, V
COM
= 1V, 4.5V, V
NO
or V
NC
= 4.5V, 1V,
Note 7
25 -0.1 0.01 0.1 nA
Full -5 - 5 nA
COM OFF Leakage Current,
I
COM(OFF)
V+ = 5.5V, V
COM
= 4.5V, 1V, V
NO
or V
NC
= 1V, 4.5V,
Note 7
25 -0.1 - 0.1 nA
Full -5 - 5 nA
COM ON Leakage Current,
I
COM(ON)
V = 5.5V, V
COM
= 1V, 4.5V, or V
NO
or V
NC
= 1V,
4.5V, or Floating, Note 7
25 -0.2 - 0.2 nA
Full -10 - 10 nA
ISL84541, ISL84542, ISL84543, ISL84544
