10
FN3179.7
January 23, 2013
This is of major importance for surface mount applications
where capacitor size and cost are critical. Smaller
capacitors, such as 0.1µF, can be used in conjunction with
the Boost Pin to achieve similar output currents compared to
the device free running with C
1
= C
2
= 10µF or 100µF. (see
Figure 11).
Increasing the oscillator frequency can also be achieved by
overdriving the oscillator from an external clock, as shown in
Figure 16. In order to prevent device latchup, a 1kΩ resistor
must be used in series with the clock output. In a situation
where the designer has generated the external clock
frequency using TTL logic, the addition of a 10kΩ pull-up
resistor to V+ supply is required. Note that the pump
frequency with external clocking, as with internal clocking,
will be one-half of the clock frequency. Output transitions
occur on the positive going edge of the clock.
It is also possible to increase the conversion efficiency of the
ICL7660S and ICL7660A at low load levels by lowering the
oscillator frequency. This reduces the switching losses, and
is shown in Figure 17. However, lowering the oscillator
frequency will cause an undesirable increase in the
impedance of the pump (C
1
) and reservoir (C
2
) capacitors;
this is overcome by increasing the values of C
1
and C
2
by
the same factor by which the frequency has been reduced.
For example, the addition of a 100pF capacitor between pin
7 (OSC and V+) will lower the oscillator frequency to 1kHz
from its nominal frequency of 10kHz (a multiple of 10), and
thereby necessitate a corresponding increase in the value of
C
1
and C
2
(from 10µF to 100µF).
Positive Voltage Doubling
The ICL7660S and ICL7660A may be employed to achieve
positive voltage doubling using the circuit shown in Figure
18. In this application, the pump inverter switches of the
ICL7660S and ICL7660A are used to charge C
1
to a voltage
level of V+ -V
F
, where V+ is the supply voltage and V
F
is the
forward voltage on C
1
, plus the supply voltage (V+) is
applied through diode D
2
to capacitor C
2
. The voltage thus
created on C
2
becomes (2V+) - (2V
F
) or twice the supply
voltage minus the combined forward voltage drops of diodes
D
1
and D
2
.
The source impedance of the output (V
OUT
) will depend on
the output current, but for V+ = 5V and an output current of
10mA, it will be approximately 60Ω.
Combined Negative Voltage Conversion and
Positive Supply Doubling
Figure 19 combines the functions shown in Figure 15 and
Figure 18 to provide negative voltage conversion and
positive voltage doubling simultaneously. This approach
would be suitable, for example, for generating +9V and -5V
from an existing +5V supply. In this instance, capacitors C
1
and C
3
perform the pump and reservoir functions,
respectively, for negative voltage generation, while
capacitors C
2
and C
4
are pump and reservoir, respectively,
for the doubled positive voltage. There is a penalty in this
configuration which combines both functions, however, in
that the source impedances of the generated supplies will be
somewhat higher, due to the finite impedance of the
common charge pump driver at pin 2 of the device.
1
2
3
4
8
7
6
5
+
-
10µF
ICL7660S
V
OUT
V+
+
-
10µF
V+
CMOS
GATE
1kΩ
FIGURE 16. EXTERNAL CLOCKING
ICL7660A
1
2
3
4
8
7
6
5
+
-
ICL7660S
V
OUT
V+
+
-
C
2
C
1
C
OSC
FIGURE 17. LOWERING OSCILLATOR FREQUENCY
ICL7660A
1
2
3
4
8
7
6
5
ICL7660S
V+
D
1
D
2
C
1
C
2
V
OUT
=
(2V+)
- (2V
F
)
+
-
+
-
FIGURE 18. POSITIVE VOLTAGE DOUBLER
NOTE: D
1
AND D
2
CAN BE ANY SUITABLE DIODE.
ICL7660A
ICL7660S, ICL7660A