OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

FTLX3612M349

P1-P3P4-P6P7-P9P10-P12P13-P13
FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011 F i n i s a r
© Finisar Corporation 11-January-2011 Rev B1 Page 4
Diagram of Host Board Connector Block Pin Numbers and Names
II. Absolute Maximum Ratings
Parameter Symbol Min Typ Max Unit Ref.
Maximum Supply Voltage 1 Vcc3 -0.5 4.0 V
Maximum Supply Voltage 2 Vcc5 -0.5 6.0 V
Storage Temperature T
S
-40 85
°C
Case Operating Temperature T
OP
-5 70
°C
FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011 F i n i s a r
© Finisar Corporation 11-January-2011 Rev B1 Page 5
III. Electrical Characteristics (T
OP
= -5 to 70 °C, V
CC5
= 4.75 to 5.25 Volts)
Parameter Symbol Min Typ Max Unit Ref.
Main Supply Voltage Vcc5 4.75 5.25 V
Supply Voltage #2 Vcc3 3.13 3.45 V
Supply Current – Vcc5 supply Icc5 350 mA
Supply Current – Vcc3 supply Icc3 750 mA
Module total power P 3.5 W 1
Transmitter
Input differential impedance R
in
100
Ω
2
Differential data input swing Vin,pp 120 820 mV
Transmit Disable Voltage V
D
2.0 Vcc V 3
Transmit Enable Voltage V
EN
GND GND+ 0.8 V
Transmit Disable Assert Time 10 us
Receiver
Differential data output swing Vout,pp 340 650 850 mV 4
Data output rise time t
r
38 ps 5
Data output fall time t
f
38 ps 5
LOS Fault V
LOS faul
t
Vcc – 0.5 Vcc
HOST
V 6
LOS Normal V
LOS nor
m
GND GND+0.5 V 6
Power Supply Rejection PSR See Note 6 below 7
Notes:
1. Maximum total power value is specified across the full temperature and voltage range.
2. After internal AC coupling.
3. Or open circuit.
4. Into 100 ohms differential termination.
5. 20 – 80 %
6. Loss Of Signal is open collector to be pulled up with a 4.7k – 10kohm resistor to 3.15 – 3.6V. Logic 0
indicates normal operation; logic 1 indicates no signal detected.
7. Per Section 2.7.1. in the XFP MSA Specification
1
.
FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011 F i n i s a r
© Finisar Corporation 11-January-2011 Rev B1 Page 6
IV. Optical Characteristics (T
OP
= -5 to 70°C, V
CC5
= 4.75 to 5.25 Volts)
Please note that the Transmitter of the FTLX3612M3xx becomes operational within 5
seconds of power-up. This is due to the time required for the EML to reach its optimum
operating temperature.
Parameter Symbol Min Typ Max Unit Ref.
Transmitter
Output Opt. Pwr: 9/125 SMF P
OUT
-1 +2 dBm
Optical Extinction Ratio ER 8.2 dB
Optical Modulation Amplitude
ΟΜΑ
-2.1 dBm 1
Center Wavelength Spacing
100 GHz
Transmitter Center Wavelength – End
Of Life
c
X-100 X X+100 pm
Transmitter Center Wavelength –
Beginning Of Life
c
X-25 X X+25 pm
Transmitter Dispersion Penalty
(@ 800 ps/nm)
TDP
2 dB
Sidemode Supression ratio SSR
min
30 dB
Tx Jitter (SONET) 20kHz-80MHz Tx
j1
0.3 UI 2
Tx Jitter (SONET) 4MHz – 80MHz Tx
j2
0.1 UI 2
Relative Intensity Noise RIN -130 dB/Hz
Receiver
Receiver Sensitivity @ 9.95Gb/s to
10.7Gb/s
R
SENS1
-16 dBm
Receiver Sensitivity @ 11.1Gb/s to
11.3Gb/s
R
SENS2
-15 dBm
Stressed Receiver Sensitivity (OMA)
@ 11.1Gb/s
R
SENS2
-11.3 dBm
Maximum Input Power P
MAX
-1 dBm
Optical Center Wavelength
C
1270 1600 nm
Receiver Reflectance R
rx
-27 dB
Path penalty at 40km (up to 10.7Gb/s) 2 dB 3
LOS De-Assert LOS
D
-22 dBm
LOS Assert LOS
A
-28 dBm
LOS Hysteresis 0.5 dB
Notes:
1. Guaranteed minimum OMA for 9.9Gb/s - 11.3Gb/s.
2. GR-253-CORE Issue 4
3. Dispersion penalty is measured in loopback using 18 ps/(nm*km) fiber (SMF-28). Path penalty is 2dB
at 10.7Gb/s.
P1-P3P4-P6P7-P9P10-P12P13-P13

FTLX3612M349

Mfr. #:
Buy FTLX3612M349
Manufacturer:
Finisar Corporation
Description:
Fiber Optic Transmitters, Receivers, Transceivers DWDM EML, 100GHz spacing (C-Band), PIN, OC-192 IR-2, STM S-64.2b, 10GBASE-ER/EW, 10G FC, G.709, 11.3Gb/s multi-rate transceiver, single mode, XFP foot
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet