105~150W Class Constant Current Mode LED DriverⅡ
ELGT-150-Cseries
SPECIFICATION
MODEL
RATED CURRENT
RATED POWER
OUTPUT
CURRENT ADJ. RANGE
SET UP TIME
Note.4
VOLTAGE RANGE Note.3
FREQUENCY RANGE
POWER FACTOR
(Typ.)
EFFICIENCY (Typ.)
AC CURRENT(Typ.)
INPUT
INRUSH CURRENT
(Typ.)
LEAKAGE CURRENT
SAFETY STANDARDS
EMC IMMUNITY
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSION
OTHERS
NOTE
PACKING
OVER TEMPERATURE
OVER VOLTAGE
1600ms/115VAC 500ms/230VAC
(Please refer to "STATIC CHARACTERISTIC" section)
47 ~ 63Hz
<0.7mA / 240VAC
Compliance to
EN55015,EN61000-3-2 Class C (@load 60%) ; EN61000-3-3≧
;EAC TP TC 020
; GB/T17743, GB17625.1
20 ~ 95% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH℃
±℃ ℃0.03%/ (0 ~ 60 )
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
ENVIRONMENT
SAFETY &
EMC
PROTECTION
Shut down o/p voltage, re-power on to recover
Shut down o/p voltage, re-power on to recover
SHORT CIRCUIT
Hiccup mode, recovers automatically after fault condition is removed
I/P-O/P:3.75KVAC I/P-CASE:3.75KVAC O/P-CASE:1.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
CURRENT TOLERANCE
±5.0%
CONSTANT CURRENT REGION
Note.2
TOTAL HARMONIC DISTORTION
OPEN CIRCUIT VOLTAGE
(max.)
Adjustable for A/AB-Type only (via built-in potentiometer)
COLD START 65A(twidth= s measured at 50% Ipeak)/230VAC485 Per NEMA 410μ;
MAX. No. of PSUs on 16A
CIRCUIT BREAKER
3 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC
Tcase=-40 ~ +90 (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)℃
MAX. CASE TEMP.
Tcase=+90℃
Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level ( )surge immunity Line-Earth 6KV, Line-Line 4KV
;EAC TP TC 020
ENEC EN61347-1, EN61347-2-13 independent, EN62384; GB19510.1, GB19510.14;EAC TP TC 004;
1. All parameters NOT specially mentioned are measured at 230VAC input, rated and 25 of ambient temperature.current ℃
2. Please refer to "DRIVING METHODS OF LED MODULE". For DA-Type, Constant Current region is 60%~100% of maximum voltage
under rated power delivery.
3. De rating may be needed under low input voltages. Please .- refer to STATIC CHARACTERISTIC sections for details
4. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time.
5. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
6. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 75 or less.℃
7. Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com
8.The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m(6500ft).℃℃
CURRENT RIPPLE
5.0% max. @rated current
100 ~ 305VAC 142 ~ 431VDC
72 ~ 143V
1050mA
151V
525 ~ 1050mA
92%
92%
91%
1.7A / 115VAC 0.9A / 230VAC 0.7A/277VAC
230 ~ 265V
155 ~ 180V
128 ~ 150V
2 *63*319 5.5 mm (L*W*H)
0.95Kg; 16pcs / 16.0kg / 0.77CUFT
IP65 or IP67 approved
PF 0.97/115VAC, PF 0.95/230VAC, PF 0.92/277VAC@full load≧≧≧
(Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
THD< 20%(@load 50%/115VC; @load 60%/230VAC; @load 75%/277VAC)≧≧ ≧
(Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)
No load power consumption <0.5W for Blank / A / D2-Type
NO LOAD / STANDBY
POWER CONSUMPTION
Standby power consumption <0.5W for B / DA-Type
1098.95K hrs min. Telcordia SR-332 (Bellcore) 308.5Khrs min. MIL-HDBK-217F (25 )℃
105W
200VAC ~ 305VAC
100VAC ~ 180VAC
150.15W
ELGT-150-C1050
ELGT-150-C700
700mA
149.8W
105W
107 ~ 214V
225V
350 ~ 700mA
ELGT-150-C1400
54 ~ 107V
1400mA
115V
700 ~ 1400mA
105W
149.8W
DALI STANDARDS
Compliance to IEC62386-101, 102, 207 for DA-Type only
EMC EMISSION
File Name:ELGT-150-C-SPEC 2018-07-02
