1485FX Datasheet 1485DZ12, 1485B6, 1485C120 | P1-P3

Type 12 Lay-In Wireway

1485 Series

Wireway & Accessories

Application

Designed to enclose and protect electrical wiring from dirt, dust, oil and

water.

All sections and fittings are completely open on each side to allow wires

and cables to be placed into the wireway without "pulling through".

Standards

UL 870 Type 1 (unless marked1)

CSA Type 1 (unless marked1)

Complies with

NEMA Type 12

JIC EMP-1-1967

JIC EGP-1-1967

IEC 60529, IP54

Construction

Bodies and covers are formed from 14-gauge steel with 10 gauge steel

flanges.

12” x 6” size has a 12 gauge steel body with a 14-gauge cover.

Smooth continuously welded seams.

Interior surfaces are smooth to prevent wire damage during

installation.

Butt hinged cover is secured with easily operated quick release clamps.

Oil resistant gaskets are permanently secured.

Solid oil resistant gaskets are used between flanges when sections and

fittings are bolted together.

One gasket kit, complete with hardware is provided with each straight

section or fitting.

Sealing plate is supplied.

Flange junctions are sealed with gasket sealing plates, which are put in

place after wiring is completed. One is supplied with all straight sections

and most fittings; see table for exact number.

Finish

Sections and components are finished in ANSI 61 gray powder coating.

Notes

When joining a wireway section or fitting to an enclosure be sure to order a

box connector.

When joining two wireway sections, or joining a wireway section to a fitting,

a flat sealing plate is required at each junction; necessary kits are supplied

with each section and fitting. See table, extra kits may be ordered if

Quality Products. Service Excellence.

Flat Sealing Plate Angle Sealing Plate

Barrier Kit Swivel Nipple

Flexible Fitting Adjustable Fitting

Cross Fitting Cut-Off Fitting (Lay-In)

Cut-Off Fitting (Non Lay-In) Nipple

45 degree Elbow Top Opening 45 degree Elbow Inside Opening

45 degree Elbow Outside Opening 90 degree Elbow Top Opening

90 degree Elbow Inside Opening 90 degree Elbow Outside Opening

Tee Fitting Top Opening Tee Fitting Outside and Top Opening

Reducers Box Connector

12" Transposition Sections Clockwise

& Counter-Clockwise

Drop Hanger

Bracket Hanger Cover Plate

Junction Box

necessary.

When joining a lay-in wireway section or fitting to a closure plate, a box

connector, or cut-off fitting, an angle sealing plate is required at each

junction.

Necessary kits are supplied with each section and fitting - see table. Extra

kits, although not normally required, are necessary when joining lay-in

wireway to a non-lay-in section or fitting section.

Accessories

Data subject to change without notice.

Description

Sealing Plates 2.5 x 2.5 4 x 4 6 x 6 8 x 8 12 x 6

Supplied Part No. Part No. Part No. Part No. Part No.

6" Section 1 Flat 1485B6 1485C6 1485D6 1485E6 1485F6

12" Section 1 Flat 1485B12 1485C12 1485D12 1485E12 1485F12

24" Section 1 Flat 1485B24 1485C24 1485D24 1485E24 1485F24

36" Section 1 Flat 1485B36 1485C36 1485D36 1485E36 1485F36

48" Section 1 Flat 1485B48 1485C48 1485D48 1485E48 1485F48

60" Section 1 Flat 1485B60 1485C60 1485D60 1485E60 1485F60

120" Section 1 Flat 1485B120 1485C120 1485D120 1485E120 1485F120

60" Long Partition (Barrier) - - 1487CB60¹ 1487DB60¹ 1487EB60¹ 1487DB60¹

1" Nipple 1 Flat 1485BM1 1485CM1 1485DM1 - -

2" Nipple 1 Flat 1485BM2 1485CM2 1485DM2 - -

3" Nipple 1 Flat 1485BM3 1485CM3 1485DM3 - -

Box Entry Swivel Nipple 1 Angle 1485BV1 1485CV1 1485DV1 1485EV1 -

Standard Swivel Nipple 2 Angle 1485BV2 1485CV2 1485DV2 1485EV2 -

12" Transposition Clockwise 1 Flat 1485BZ12 1485CZ12 1485DZ12 1485EZ12 -

12" Transposition Counter-Clockwise 1 Flat 1485BZC12 1485CZC12 1485DZC12 1485EZC12 -

Flexible Fitting None 1485BFF 1485CFF 1485DFF 1485EFF -

Adjustable Fitting 1 Spec. 1485BX¹ 1485CX¹ 1485DX¹ 1485EX¹ 1485FX¹

Cut-Off Fitting Lay-In 1 Flat 1485BW1¹ 1485CW1¹ 1485DW1¹ 1485EW1¹ 1485FW1¹

Cut-Off Fitting Non Lay-In 1 Angle 1485BW2¹ 1485CW2¹ 1485DW2¹ 1485EW2¹ 1485FW2¹

90° Elbow, Top Opening 1 Flat 1485B9N 1485C9N 1485D9N 1485E9N 1485F9N

90° Elbow, Inside Opening 1 Flat 1485B9P 1485C9P 1485D9P 1485E9P 1485F9P

90° Elbow, Outside Opening 1 Flat 1485B9Q 1485C9Q 1485D9Q 1485E9Q 1485F9Q

45° Elbow, Top Opening 1 Flat 1485B4N 1485C4N 1485D4N 1485E4N 1485F4N

45° Elbow, Inside Opening 1 Flat 1485B4P 1485C4P 1485D4P 1485E4P -

45° Elbow, Outside Opening 1 Flat 1485B4Q 1485C4Q 1485D4Q 1485E4Q -

Tee Fitting, Top Opening 2 Flat 1485BTN 1485CTN 1485DTN 1485ETN 1485FTN

Tee Fitting, Outside & Top Opening 2 Flat 1485BTQ 1485CTQ 1485DTQ 1485ETQ -

Cross Fitting 3 Flat 1485BY 1485CY 1485DY 1485EY 1485FY

Reducer 4 x 4 to 2.5 x 2.5 None - 1485CRE - - -

Reducer 6 x 6 to 4 x 4 None - - 1485DRE - -

Reducer 8 x 8 to 6 x 6 None - - - 1485ERE -

Reducer 12 x 6 to 4 x 4 None - - - - 1485FREC

Reducer 12 x 6 to 6 x 6 None - - - - 1485FRED

Junction Box 1 Flat 1485BJ 1485CJ 1485DJ 1485EJ -

Box Connector 1 Angle 1485BK¹ 1485CK¹ 1485DK¹ 1485EK¹ 1485FK¹

Drop Hanger None 1485BL1¹ 1485CL1¹ 1485DL1¹ 1485EL1¹ -

Bracket Hanger None 1485BL2¹ 1485CL2¹ 1485DL2¹ 1485EL2¹ -

Cover Plate 1 Angle 1485BH² 1485CH² 1485DH² 1485EH² 1485FH²

Snap On Flat Sealing Plate None 1485BSM² 1485CSM² 1485DSM² 1485ESM² 1485FSM²

Angle Sealing Plate None 1485BS9² 1485CS9² 1485DS9² 1485ES9² 1485FS9²

¹ Does not meet CSA or UL requirement

² Maintains ratings on CSA and UL approved wireway

P1-P3

1485FX

Mfr. #:

Buy 1485FX

Manufacturer:

Hammond Manufacturing

Description:

Wire Ducting & Raceways Adj.Fitting from 2-7 for 8x8" Wireway

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

1485FX

1485FX

Products related to this Datasheet