Air performance measured according to: ISO 5801.
Installation category A, without contact protection.
Noise: Total sound power level L
W
A ISO 103002
measured on a hemisphere with a radius of 2 m.
Sound pressure level L
p
A measured at 1 m distance from
fan axis.
The values given are applicable only under the specified
measuring conditions and may differ depending on the
installation conditions.
In the event of deviation from the standard configuration,
the parameters must be checked after installation!
For detailed information see
http://www.ebmpapst.com/general conditions
– Possible special versions:
(See chapter DC fans - specials)
- Speed signal
- Go / NoGo alarm
- Alarm with speed limit
- External temperature sensor
- Internal temperature sensor
- PWM control input
- Analog control input
- Multi-option control input
- Moisture protection
- Salt spray protection
- Degree of protection: IP 54
Max. 1220 m
3
/h
Type m
3
/h cfm VDC VDC dB(A) Bel(A) / Watts rpm
-1
°C Hours Hours
2214 F/2 TDHO 790 465 24 16...30 62 7.1 35 4250 -20...+75 90 000 / 42 500 152 500 ¿
2214 F/2 TDHHO 940 553 24 16...36 66 7.4 48 5000 -20...+70 85 000 / 42 500 142 500 ¡
2218 F/2 TDHO 790 465 48 36...57 62 7.1 35 4250 -20...+75 90 000 / 42 500 152 500 ¿
2218 F/2 TDHHO 940 553 48 36...72 66 7.4 48 5000 -20...+70 85 000 / 42 500 142 500 ¡
2218 F/2 TDH4P 1220 718 48 36...72 72 8.2 103 6500 -20...+65 70 000 / 40 000 117 500 ¬
Subject to change
Nominal voltage
Air flow
Air flow
Voltage range
Sound pressure level
Sound power level
Sintec sleeve bearings
Ball bearings
Power consumption*
Nominal speed
Temperature range
Service life L
10
(40 °C)
ebm-papst standard
Service life L
10
(T
max
)
ebm-papst standard
Life expectancy L
10IPC
(40 °C) see page 17
Curve
– Material: Housing: Die-cast aluminum
Impeller: GRP
1)
(PA)
– Direction of air flow: Exhaust over struts
– Direction of rotation: Counterclockwise,
looking towards rotor
– Connection: Via single wires AWG 18, 20 or
AWG 22, TR 64, speed signal
and control input AWG 22
– Highlights: Highly efficient and smoothly
operating 3-phase fan drive
Housing with grounding lug
for screw M4 x 8 (Torx)
– Weight: 1000 g
1) Fiberglass-reinforced plastic
7.6 deep
Speed control range from 1000 rpm
-1
up to maximum nominal speed.
Standstill at 0% PWM, Type O: standstill if control wire is interrupted; Type P: maximum speed if control wire is interrupted.
* Power consumption at free air flow. These values can be significantly higher in the operating point.
Tin-plated
81
2016-01
Information
DC axial fansDC fans - specials
ACmaxx / EC fans
AC axial fans
Accessories
Representatives
DC centrifugal fansAC centrifugal fans
Finger guards
from p. 242
6 3 4 3 6 7 7 4 - 7 1
7 4 4 3 7 8 1 4 - 6 1
1 6 4 3 7 8 3 6 - 5 8
1 6 4 3 7 8 3 6 - 4 6
DC axial fans
220 x 200 x 51 mm
Series 2200 FTD
Nominal data
