Data Sheet ADPD2210
Rev. A | Page 3 of 15
SPECIFICATIONS
V
CC
= 3.3 V T
A
= 25°C, unless otherwise noted. N
SHOT
is shot noise. E
E
is irradiance.
Table 1.
Parameter Symbol Test Conditions/Comments
Min Typ Max
Unit
GAIN
Current Gain β
TLA
V
BIAS
= 0 V 23.7 24.2 24.8
DYNAMIC PERFORMANCE
Power-Down Recovery Time
t
RECOVER
1% full-scale (FS) output
100 nA to 1 μA 50 μs
1 μA to 10 μA 20 μs
Rise t
RISE
10% to 90% FS (240 μA) 5 μs
Fall t
FALL
90% to 10% FS (240 μA) 5 μs
Bandwidth I
IN
= 100 nA (dc), 100 nA (ac) 125 kHz
I
IN
= 1 μA (dc), 100 nA (ac) 85 kHz
INPUT
Input Capacitance C
IN_MAX
8 pF
Nominal Input Current I
IN_MAX
10 μA
Input Offset Voltage V
IN_REF
±5 mV
Reference Voltage REF V
CC
− 1.2 V
STATIC BIAS
Input Referred I
SB
10 nA
Output Referred O
SB
240 nA
NOISE PERFORMANCE
Current Noise Floor, Input Referred I
IN
I
IN
< 10 nA 80 150 fA/√Hz
Current Noise, Input Referred I
IN
= 100 nA,1.5 × N
SHOT
260 fA/√Hz
I
IN
= 1μA, 1.15 × N
SHOT
740 fA/√Hz
POWER AND SUPPLY
Supply Voltage V
CC
1.8 3.3 5 V
Standby Current I
STANDBY
PWDN > V
IH
100 nA
Power Supply Rejection Ratio
PSRR V
CC
= 1.8 V to 5.0 V, E
E
= 10 μA
25 nA/V
Supply Current Floor I
FLOOR
I
IN
= 0 pA 140 μA
Supply Current I
SUPPLY
I
OUT
= 10 μA 167 μA
I
OUT
= 240 μA, I
SUPPLY
= I
FLOOR
+ (3.3 × I
OUT
) 954 μA
OUTPUT CHARACTERISTICS
Maximum Output Voltage V
OUT_MAX
V
CC
= 3.3 V, I
OUT
= 240 μA V
CC
− 0.75 V
Nominal Linear Output I
OUT_FS
V
CC
= 3.3 V 240 μA
V
CC
= 1.8 V 65 μA
Linearity
TIA, V
BIAS
= 0 V, R
FEEDBACK
= 25 kΩ
I
IN
= 200 nA to 4 μA 0.1 %
I
IN
= 200 nA to 10 μA 0.3 %
Resistor I
IN
= 200 nA to 4 μA, R
LOAD
= 5kΩ 0.1 %
Peak Output Current I
OUT_PEAK
V
CC
= 3.3 V 300 μA
V
CC
= 1.8 V 65 μA
Output Capacitance C
OUT
From OUT to GND 5 pF
Output Resistance R
OUT
From OUT to GND >5
POWER-DOWN LOGIC
Input Voltage
High V
IH
V
CC
− 0.2 V
Low V
IL
0.2 V
Leakage Current
High
I
IH
PWDN = 3.3 V 0.2 nA
Low
I
IL
PWDN = 0 V −8.5 μA
ADPD2210 Data Sheet
Rev. A | Page 4 of 15
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter Rating
Supply Voltage, V
CC
6 V
Storage Temperature Range −65°C to +150°C
Operating Ambient Temperature Range −40°C to +85°C
Maximum Junction Temperature 150°C
Solder Reflow Temperature (<10 sec) 260°C
Current into IN Pin 1 mA
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
THERMAL RESISTANCE
θ
JA
is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 3. Thermal Resistance
Package Type θ
JA
θ
JC
Unit
2 mm × 2 mm LFCSP 84.4 12.32 °C/W
ESD CAUTION
Data Sheet ADPD2210
Rev. A | Page 5 of 15
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 2. Pin Configuration
Table 4. Pin Function Descriptions
Pin No. Mnemonic Description
1 PWDN
Power-Down Input. Tie the PWDN pin to ground for normal operation. Connecting this input to a logic high
enables standby mode. Do not leave this input floating.
2 OUT Current Output.
3 GND Ground.
4 REF
Voltage Reference Output. REF is nominally 1.2 V below V
CC
. This pin is the matched voltage reference for the
current input and is typically tied to the cathode of a photodiode. Attachment to this terminal is not required.
5 IN Current Input (Sink). The voltage of the IN pin is forced within 5 mV of the reference input.
6 VCC Supply.
7 EPAD Exposed Pad. Connect the EPAD to GND.
NOTE
1. CONNECT THE
E
PAD TO GND.
3
GND
1
PWDN
2
OUT
REF
VCC
IN
ADPD2210
EPAD(7)
4
6
5
CURRENT
AMPLIFIER
12286-001

ADPD2210ACPZ-R7

Mfr. #:
Manufacturer:
Analog Devices Inc.
Description:
Photo IC Sensors UltraLowNoise Integr Intensity Sensor
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet