MAX5541
Low-Cost, +5V, Serial-Input,
Voltage-Output, 16-Bit DAC
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(V
DD
= +5V ±5%, V
REF
= +2.5V, V
AGND
= V
DGND
= 0, T
A
= T
MIN
to T
MAX
, unless otherwise noted. Typical values are at T
A
= +25°C.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
V
DD
to DGND............................................................-0.3V to +6V
CS, SCLK, DIN to DGND..........................................-0.3V to +6V
REF to AGND, DGND..................................-0.3V to (V
DD
+0.3V)
AGND to DGND.....................................................-0.3V to +0.3V
OUT to AGND, DGND.................................. ............-0.3V to V
DD
Maximum Current into Any Pin............................................50mA
Continuous Power Dissipation (T
A
= +70°C)
8-Pin SO (derate 5.88mW/°C above +70°C)................471mW
Operating Temperature Ranges
MAX5541CSA .....................................................0°C to +70°C
MAX5541ESA ..................................................-40°C to +85°C
Junction Temperature......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) ................................ +300°C
(Note 5)
(Note 4)
4.75V ≤ V
DD
≤ 5.25V
T
A
= T
MIN
to T
MAX
T
A
= +25°C
T
A
= T
MIN
to T
MAX
T
A
= +25°C
T
A
= T
MIN
to T
MAX
(Note 3)
CONDITIONS
kΩ11.5R
REF
Reference Input Resistance
V2.0 3.0V
REF
Reference Input Range
PSRPower-Supply Rejection LSB±1.0
R
OUT
DAC Output Resistance kΩ6.25
Bits16NResolution
ppm/°C±0.1Gain-Error Tempco
LSB
±10
Gain Error (Note 2)
±5
ppm/°C±0.05ZS
TC
Zero-Code Tempco
LSBINLIntegral Nonlinearity ±4 ±16
±1
±2
Zero-Code Offset Error
UNITSMIN TYP MAXSYMBOLPARAMETER
ZSE LSB
To ±
1
/
2
LSB of FS, C
L
= 10pF
1 µsOutput Settling Time
V
DD
= 5V (Note 1)
Guaranteed monotonic Bits±0.5 ±1.0DNLDifferential Nonlinearity
C
L
= 10pF (Note 6) 25 V/µsSRVoltage Output Slew-Rate
Major-carry transition 10 nVsDAC Glitch Impulse
Code = 0000 hex, CS = V
DD
,
SCLK = V
DIN
= 0 to V
DD
levels
10 nVsDigital Feedthrough
Code = FFFF hex 1 MHzBWReference -3dB Bandwidth
DYNAMIC PERFORMANCE—REFERENCE SECTION
Code = 0000 hex, V
REF
= 1V
P-P
at 100kHz 1 mV
P-P
Reference Feedthrough
92 dBSNRSignal-to-Noise Ratio
Code = 0000 hex 75
pFC
IN
Reference Input Capacitance
STATIC PERFORMANCE—ANALOG SECTION (R
L
= ∞)
REFERENCE INPUT
DYNAMIC PERFORMANCE—ANALOG SECTION (R
L
= ∞)
Code = FFFF hex 120
