3/7
www.rohm.com
○
c
2012 ROHM Co., Ltd. All rights reserved.
2012.03 - Rev.H
Data Sheet TCFG Series A Case
Item Performance
Test conditions
(based on JIS C5101-1 and JIS C5101-3)
Operating Temperature
Maximum operating temperature
with no voltage derating
Rated Voltage (V.DC)
16106.34
Category Voltage (V.DC)
106.342.5
Surge Voltage
20
20
13
26
25
16
321385.0
DC leakage current
0.5μA or 0.01CV whichever is greater
(Shown in "Standard list")
As per 4.9 JIS C 5101-1
As per 4.5.1 JIS C 5101-3
As per 4.7 JIS C 5101-1
As per 4.5.2 JIS C 5101-3
As per 4.8 JIS C 5101-1
As per 4.5.3 JIS C 5101-3
As per 4.10 JIS C 5101-1
As per 4.5.4 JIS C 5101-3
As per 4.14 JIS C 5101-1
As per 4.6 JIS C 5101-3
As per 4.16 JIS C 5101-1
As per 4.10 JIS C 5101-3
As per 4.12 JIS C 5101-1
As per 4.12 JIS C 5101-3
Voltage : Rated voltage for 1min
Capacitance tolerance
Shall be satisfied allowance range.
±
20%
Measuring frequency
Measuring voltage
Measuring circuit
Tangent of loss angle
(Df, tanδ)
Impedance
Shall be satisfied the voltage on "Standard list"
Dip in the solder bath
Solder temp
Duration
Repetition
After the specimens, leave it at room temperature fo
over 24h and then measure the sample.
Resistance to
soldering heat
There should be no significant abnormality.
The indications should be clear.
Appearance
Less than initial limit
L.C
Shall be satisfied the voltage on "Standard list"
at 125
°C
at 85
°C
at 85
°C
+85
°C
: 120
±
12Hz
: 0.5Vrms, +1.5V.DC
: DC Equivalent series circuit
Measuring frequency
Measuring voltage
Measuring circuit
: 120
±
12Hz
: 0.5Vrms, +1.5V.DC
: DC Equivalent series circuit
: 100
±
10kHz
: 0.5Vrms or less
Measuring frequency
Measuring voltage
: 260
±5°C
: 5
±
0.5s
: 1
−55
°C to
+125
°C
Voltage reduction when temperature exceeds +85°C
Fail-Safe open unit actuation
Within
320
°C
− 20s
Repetition : 5 cycles (1 cycle : steps 1 to 4)
without discontinuation.
Temperature
cycle
There should be no significant abnormality.
The indications should be clear.
Appearance
Less than initial limit
L.C
Within
±
5
% of initial value
ΔC / C
tanδ
ΔC / C
tanδ
Less than initial limit
Less than initial limit
Moisture
resistance
Appearance
Less than initial limit
L.C
There should be no significant abnormality.
The indications should be clear.
Temp. Time
1
Step
2
3
4
Room temp.
Room temp.
3min. or less
3min. or less
30 3min
+
−
30 3min
+
−
−55 3
°C
+
−
125 2°C
+
−
ΔC / C
Within
±
10
% of initial value
Less than initial limit
tanδ
After leaving the sample under such atmospheric
condition that the temperature and humidity are
60
±
2
°C
and 90 to 95%RH, respectively, for
500
±
12h level it at room temperature for over
24h and then measure the sample.
Dip in the solder bath
Solder temp : 320
±
5
°C
Others
: Within
±
10
% of initial value
TCFGA1A226M8R
: Within
±
15
% of initial value
TCFGA0J476M8R
: Within
±
15
% of initial value
TCFGA0G686M8R
: Within
±
15
% of initial value
After the specimens, leave it at room temperature fo
over 24h and then measure the sample.