C8051F300-GDI

C8051F300-GDI
Rev. 1.1 4/12 Copyright © 2012 by Silicon Laboratories C8051F300-GDI
8 kB Flash, 8-Bit ADC MCU Die in Wafer Form
Analog Peripherals
- 8-Bit ADC
Up to 500 ksps
Up to 8 external inputs
Programmable amplifier gains of 4, 2, 1, & 0.5
VREF from external pin or V
DD
Built-in temperature sensor
External conversion start input
- Comparator
Programmable hysteresis and response time
Configurable as interrupt or reset source
Low current (0.5 µA)
On-chip Debug
-
On-chip debug circuitry facilitates full speed, non-
intrusive in-system debug (no emulator required)
- Provides breakpoints, single stepping,
inspect/modify memory and registers
- Superior performance to emulation systems using
ICE-chips, target pods, and sockets
Supply Voltage 2.7 to 3.6 V
-
Typical operating current: 6.6 mA @ 25 MHz;
14 µA @ 32 kHz
- Typical stop mode current: 0.1 µA
- Temperature range: –40 to +85 °C
Full Technical Data Sheet
-
C8051F300/1/2/3/4/5
High Speed 8051 µc Core
-
Pipelined instruction architecture; executes 70% of
instructions in 1 or 2 system clocks
- Up to 25 MIPS throughput with 25 MHz clock
- Expanded interrupt handler
Memory
-
256 bytes internal data RAM
- 8 kB Flash; 512 bytes are reserved in the 8 kB
devices
Digital Peripherals
-
8 Port I/O; All 5 V tolerant with high sink current
- Hardware enhanced UART and SMBus™ serial
ports
- Three general-purpose 16-bit counter/timers
- 16-bit programmable counter array (PCA) with three
capture/compare modules
- Real time clock mode using PCA or timer and
external clock source
Clock Sources
-
Internal oscillator: 24.5 MHz with ±2% accuracy
supports UART operation
- External oscillator: Crystal, RC, C, or clock (1 or 2
pin modes)
- Can switch between clock sources on-the-fly; Useful
in power saving modes
ANALOG
PERIPHERALS
PGA
8/4/2 kBytes
ISP Flash
256 B SRAM
POR
DEBUG
CIRCUITRY
12
INTERRUPTS
8051 CPU
(25MIPS)
DIGITAL I/O
PROGRAMMABLE PRECISION INTERNAL
OSCILLATOR
HIGH-SPEED CONTROLLER CORE
A
M
U
X
I/O Port
CROSSBAR
UART
SMBus
PCA
Timer 0
Timer 1
Timer 2
VOLTAGE COMPARATOR
+
-
WDT
8-bit
500 ksps
ADC
TEMP
SENSOR
C8051F300/2 only
C8051F300-GDI
2 Rev. 1.1
1. Ordering Information
Table 1.1. Product Selection Guide
Ordering Part Number
MIPS (Peak)
Flash Memory (kB)*
RAM (Bytes)
SMBus/I
2
C
UART
Timers (16-bit)
Programmable Counter Array
Digital Port I/Os
8-bit 500 ksps ADC
Programmable Current Reference
Temperature Sensor
Analog Comparators
Lead-free (RoHS Compliant)
Package
C8051F300-GDI 25 8 256 1 1 3 8  1 Tested Die
in Wafer
Form
*Note: 512 bytes reserved for factory use.
Rev. 1.1 3
C8051F300-GDI
2. Pin Definitions
Table 2.1. Pin Definitions for the C8051F300-GDI
Name Physical Pad
Number
Type Description
VREF /
P0.0
3A In
D I/O or
A In
External Voltage Reference Input.
Port 0.0.
P0.1 4 D I/O or A
In
Port 0.1.
V
DD
5 Power Supply Voltage.
XTAL1 /
P0.2
6A In
D I/O or A
In
Crystal Input. This pin is the external oscillator circuit return
for a crystal or ceramic resonator.
Port 0.2.
XTAL2 /
P0.3
7 A Out
D I/O
Crystal Input/Output. For an external crystal or resonator, this
pin is the excitation driver. This pin is the external clock input
for CMOS, capacitor, or RC network configurations.
Port 0.3.
P0.4 13 D I/O or A
In
Port 0.4.
P0.5 14 D I/O or A
In
Port 0.5.
C2CK /
RST
15 D I/O
D I/O
Clock signal for the C2 Development Interface.
Device Reset. Open-drain output of internal POR or V
DD
monitor. An external source can initiate a system reset by
driving this pin low for at least 10 µs.
P0.6 /
CNVSTR
16 D I/O or
A In
D I/O
Port 0.6.
ADC External Convert Start Input Strobe.
C2D /
P0.7
17 D I/O
D I/O or
A In
Data signal for the C2 Development Interface.
Port 0.7.
GND 18 Ground.

C8051F300-GDI

Mfr. #:
Manufacturer:
Silicon Labs
Description:
8-bit Microcontrollers - MCU Actual die quantities will vary +/- 10% of the MOQ. All orders must be in multiples of the MOQ. All parts tested to the same level as packaged parts.
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet