© TT electronics plc
General Note
TT Electronics reserves the right to make changes in product specification without
notice or liability. All information is subject to TT Electronics’ own data and is
considered accurate at time of going to print.
Photologic® Reflective Object
Sensor
OPB760, OPB761, OPB762, OPB763 (Series N and T)
OPB770, OPB771, OPB772, OPB773 (Series NZ and TZ)
Issue C 05/2016 Page 4
OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
www.optekinc.com | www.ttelectronics.com
Electrical Specifications
Absolute Maximum Ratings
(T
A
=25°C unless otherwise noted)
Supply Voltage, V
CC
(not to exceed 3 seconds) 10 V
Storage Temperature Range -40° C to +85° C
Operating Temperature Range -40° C to +70° C
Lead Soldering Temperature (1/16” inch (1.6 mm) from case for 5 seconds with soldering iron)
(1)
260° C
Input Diode Power Dissipation
(2)
100 mW
Output Photologic® Power Dissipation
(3)
200 mW
Total Device Power Dissipation
(4)
300 mW
Voltage at Output Lead (Open Collector Output) 35 V
Diode Forward DC Current 40 mA
Diode Reverse DC Voltage 3 V
Electrical Characteristics (T
A
= 25°C unless otherwise noted)
SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS
Input Diode
V
F
Forward Voltage - - 1.8 V I
F
= 40 mA, T
A
= 25° C
I
R
Reverse Current - - 100 μA V
R
= 2.0 V, T
A
= 25° C
Output Photologic® Sensor
V
CC
Operating DC Supply Voltage 4.75 - 5.25 V
I
CCL
Low Level Supply Current:
Buffered Totem-Pole Output
(5)(6)
Buffered Open-Collector Output
(5)(6)
-
-
-
-
10
10
mA
mA
Vcc = 5.25 V, If = 0 mA
(output open)
Inverted Totem-Pole Output
(5)
Inverted Open-Collector Output
(5)
-
-
-
-
10
10
mA
mA
Vcc = 5.25 V, If = 25 mA (output open)
I
CCH
High Level Supply Current:
Buffered Totem-Pole Output
(5)(6)
Buffered Open-Collector Output
(5)
-
-
-
-
10
10
mA
mA
Vcc = 5.25 V, If = 25 mA
(output open)
Inverted Totem-Pole Output
(5)(6)
Inverted Open-Collector Output
(5)(6)
-
-
-
-
10
10
mA
mA
Vcc = 5.25 V, If = 0 mA
(output open)
I
OH
High Level Output Current:
Buffered Open-Collector Output
-
-
-
-
100
100
μA
μA
Vcc = 4.5 V, If = 25 mA, V
OH
= 30 V, T
A
=25°C
Inverted Open-Collector Output - - 100 μA Vcc = 4.5 V, If = 0 mA, V
OH
= 30 V, T
A
= 25°C
Notes:
(1) RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering.
(2) Derate linearly 2.22 mW/°C above 25° C.
(3) Derate linearly 4.44 mW/°C above 25° C.
(4) Derate linearly 6.66 mW/°C above 25° C.Normal application would be with light source blocked, simulated by I
F
=0 mA.
(5) Tested at d = 0.080” (mm) from a 90% diffuse white test surface.
(6) Normal application would be with light source blocked, simulated by I
F
= 0 mA.
(7) All parameters tested using pulse technique.
