OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

SLA-580MT3F

P1-P3P4-P6P7-P9P10-P12
[SLI-580x/SLA-580x/SLA580x series]
　　　　
[Data Sheet]
■Part No. Construction
*"-"will be taken out for emitting color Special Code will be applied for Chromaticity rank Rank sign
WB/B/E series. Emitting color WB/B/E series. (for white LED） (Brightness Rank)*
Series name Package type Emitting Color Resin Color Taping Specification
V R
U U
U2 Y
D G
Y C
Y2 RC
M T
P
E
B
*Concerning the Brightness rank.
WB
*Please refer to the rank chart above for
luminous intensity classification.
*Part name is individual for each rank.
*When shipped as sample,the part name will
be a representative part name.
General products are free of ranks.
Please contact sales if rank appointment
is needed.
Green
Green
Blue
White
Yellow
Transparent Colored
Yellow
Yellowish green
Transparent Coloreless
SLR 1-Die Circular Type LED Lamps Red
<Yellow>DiffusedColored
SLD
1-Die Oval Type High Brightness LED Lamps
Orange
<Yellowish green>DiffusedColored
SLA
1-Die Circular Type High Brightness LED Lamps
Red
<Red>DiffusedColored
SLI
1-Die Circular Type Low Current High Brightness LED Lamps
Red
<Orange>DiffusedColored
8S L I － 5
See Taping specifications
3F
T□□
20 U T T 3 XS
1-Element straight bulk
＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿
www.rohm.com
©2016 ROHM Co., Ltd. All rights reserved
7/10
2017.9 - Rev.004
[SLI-580x/SLA-580x/SLA580x series]
　　　　
[Data Sheet]
Visual light emitting diode does not contain reinforcement materials such as glass fillers.
Therefore if sudden thermal and mechanical shock are given, destruction or inferiority of luminous
intensity may occur. Please take care of the handling.
Please consult with us if any problems in the evaluation stage.
■ATTENTION POINTS IN HANDLING
　　of LED body.
　　If stress is given during processing, It may cause
　　non-lighting failure.
　(3) Please process before soldering.
３． ASSEMBLY ON PC BOARD
２． TERMINATION PROCESSING
　(1) In case of termination processing, please fix the
　　termination
　(2) Processing position, and process the reverse side
■FIXATION METHOD
１．ATTENTION POINTS
　(1) Please do not give excessive heat over storage temperature to resin.
　　In case that the product has to be heated in oven for the glue fixing of surface mount parts,
　　this LED should be mounted after the glue fixing.
　(2) Please avoid stress to resin at high temperature.
　(1) In case of soldering on PCB, If the operation is done with stress, it may cause non-lighting
　　failure during soldering or using. Please design the through-holes of PCB suitable for lead pins
　　space or lead pins space after forming to avoid the physical stress on resin.
　(2) Using spacer between LEDʼs body and PCB is recommended.
　　In case of direct mount on PCB(SLR/SLI-343 series), please take care about clinch of LED pins
　　to avoid the remained stress and solder heat stress.
　　
Enough evaluation is requested before deciding assembly and soldering conditions.
＜Good＞ ＜No good＞
To be fixed To be fixed
＜Good＞ ＜No good＞＜Good＞
＜2 lead pins type＞
＜3 lead pins type＞
Min.15°
Min.45°
Die bonding side
＜2 lead pin type＞
Min.15°
Min.45°
Die bonding side
Min.45
＜3 lead pin type＞
＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿
www.rohm.com
©2016 ROHM Co., Ltd. All rights reserved
8/10
2017.9 - Rev.004
[SLI-580x/SLA-580x/SLA580x series]
　　　　
[Data Sheet]
＜RECOMMENDABLE STORAGE CONDITIONS＞
CONDITIONS
5〜30℃
Max.60%RH
Within 1 year
The iron should not touch the LEDʼs body.
　The recommendable cleaning solvent is alcoholic one such as isopropyl alcohol.
＜RECOMMENDABLE CLEANING CONDITIONS＞
METHOD
CONDITIONS
Cleaning by solvent
５．CLEANING
　In case of cleaning, some solvents may cause damage of resin or cause non-lighting failure,
Temperature of solvent
：Max. 45℃
Immersion time
：Max. 3min
Soldering Iron
Max. 400℃
3sec Max.
Cleaning by solvent
Cleaning time
：Max. 3min
■ATTENTION ON STORAGING
Poor storage conditions may cause some failure as bellow.
　　luminous intensity may occur.
ARTICLE
Temperature
Humidity
Expiration Date
　(2) In case of soldering after LEDʼs body absorb moisture highly, destruction or inferiority of
　Storage in dry box is most desirable, but if it is not possible, we recommend following conditions.
　(1) Lead pins may corrode if it is stored in the environment of high temperature and humidity
　　and lead to defective soldering.
Ultrasonic out
：Max. 15W/Liter
６．RECOMMENDABLE ROUND PATTERN
　　Round pattern depends on the material PCB, density and circuit arrangement.
　　Our recommendation is as follow :
　so please check the solvent before actual use.
４．SOLDERING（Sn-3Ag-0.5Cu）
　(1) Please make soldering rapidly under the following temperature and time conditions.
　(2) Please avoid stress to LED lamp during soldering.
　(3) In case of double peak flow soldering, the temperature gap during 1st and 2nd soldering to be
　　less than 100 degree C.
＜Recommendable soldering conditions＞
ARTIICLE
SOLDERINGTEMP
OPERATION TIME
Remarks
Pre-heat
Max. 100℃
60sec Max.
－
Soldering Dip
Soldering Bath
Max. 265℃ 5sec Max.
In case of double peak flow soldering, the operation
time is counted from the beginning of 1st peak
to the end of 2nd peak.
<2 lead pin type> <3 lead pin type/2.5mm pitch>
＜3 lead pin type/2.0mm pitch>
1.5
±0.1
1.0
2.0
2.0
φ2.0
2.0
2.5
or
5.0
±0.1
1.0
2.0
±0.1
1.0
2.5
2.5
＊Unit : mm
＊Lead types : □0.4mm
□0.5mm
＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿
www.rohm.com
©2016 ROHM Co., Ltd. All rights reserved
9/10
2017.9 - Rev.004
P1-P3P4-P6P7-P9P10-P12

SLA-580MT3F

Mfr. #:
Buy SLA-580MT3F
Manufacturer:
ROHM Semiconductor
Description:
Standard LEDs - Through Hole GREEN HI BRITE TRANS LENS
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet