OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

ADUM6000ARIZ-RL

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P17
Data Sheet ADuM6000
Rev. D | Page 3 of 16
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS—5 V PRIMARY INPUT SUPPLY/5 V SECONDARY ISOLATED SUPPLY
4.5 V ≤ V
DD1
≤ 5.5 V, V
SEL
= V
ISO
; each voltage is relative to its respective ground. Minimum/maximum specifications apply over the entire
recommended operating range, unless otherwise noted. Typical specifications are at T
A
= 25°C, V
DD1
= 5.0 V, V
ISO
= 5.0 V, and V
SEL
= V
ISO
.
Table 2.
Parameter Symbol Min Typ Max Unit Test Conditions/Comments
DC-TO-DC CONVERTER POWER SUPPLY
Setpoint
V
ISO
4.7
5.0
V
I
ISO
= 0 mA
Line Regulation V
ISO(LINE)
1 mV/V I
ISO
= 40 mA, V
DD1
= 4.5 V to 5.5 V
Load Regulation V
ISO(LOAD)
1 5 % I
ISO
= 8 mA to 72 mA
Output Ripple V
ISO(RIP)
75 mV p-p 20 MHz bandwidth, C
BO
= 0.1 μF||10 μF,
I
ISO
= 72 mA
Output Noise V
ISO(N)
200 mV p-p C
BO
= 0.1 μF||10 μF, I
ISO
= 72 mA
Switching Frequency f
OSC
180 MHz
PWM Frequency f
PWM
625 kHz
I
DD1
Supply Current, Full V
ISO
Load I
DD1(MAX)
290 mA
Maximum Output Supply Current I
ISO(MAX)
80 mA V
ISO
> 4.5 V
Efficiency at Maximum Output
Supply Current
31 % I
ISO
= 80 mA
I
DD1
Supply Current, No V
ISO
Load I
DD1(Q)
7 16 mA I
ISO
= 0 mA
Undervoltage Lockout, V
DD1
and V
ISO
Supplies
UVLO
Positive-Going Threshold V
UV+
2.7 V
Negative-Going Threshold V
UV−
2.4 V
Hysteresis V
UVH
0.3 V
ELECTRICAL CHARACTERISTICS—3.3 V PRIMARY INPUT SUPPLY/3.3 V SECONDARY ISOLATED SUPPLY
3.0 V ≤ V
DD1
≤ 3.6 V, V
SEL
= GND
ISO
; each voltage is relative to its respective ground. Minimum/maximum specifications apply over the entire
recommended operating range, unless otherwise noted. Typical specifications are at T
A
= 25°C, V
DD1
= 3.3 V, V
ISO
= 3.3 V, and V
SEL
= GND
ISO
.
Table 3.
Parameter Symbol Min Typ Max Unit Test Conditions/Comments
DC-TO-DC CONVERTER POWER SUPPLY
Setpoint V
ISO
3.0 3.3 3.6 V I
ISO
= 0 mA
Line Regulation V
ISO(LINE)
1 mV/V I
ISO
= 20 mA, V
DD1
= 3.0 V to 3.6 V
Load Regulation V
ISO(LOAD)
1 5 % I
ISO
= 4 mA to 36 mA
Output Ripple V
ISO(RIP)
50 mV p-p 20 MHz bandwidth, C
BO
= 0.1 μF||10 μF,
I
ISO
= 36 mA
Output Noise V
ISO(N)
130 mV p-p C
BO
= 0.1 μF||10 μF, I
ISO
= 36 mA
Switching Frequency f
OSC
180 MHz
PWM Frequency f
PWM
625 kHz
I
DD1
Supply Current, Full V
ISO
Load I
DD1(MAX)
175 mA
Maximum Output Supply Current I
ISO(MAX)
40 mA V
ISO
> 3.0 V
Efficiency at Maximum Output
Supply Current
31
%
I
ISO
= 40 mA
I
DD1
Supply Current, No V
ISO
Load I
DD1(Q)
5 13 mA I
ISO
= 0 mA
Undervoltage Lockout, V
DD1
and V
ISO
Supplies
UVLO
Positive-Going Threshold V
UV+
2.7 V
Negative-Going Threshold
UV−
2.4
V
Hysteresis V
UVH
0.3 V
ADuM6000 Data Sheet
Rev. D | Page 4 of 16
ELECTRICAL CHARACTERISTICS—5 V PRIMARY INPUT SUPPLY/3.3 V SECONDARY ISOLATED SUPPLY
4.5 V ≤ V
DD1
≤ 5.5 V, V
SEL
= GND
ISO
, each voltage is relative to its respective ground. Minimum/maximum specifications apply over the entire
recommended operating range, unless otherwise noted. Typical specifications are at T
A
= 25°C, V
DD1
= 5.0 V, V
ISO
= 3.3 V, and V
SEL
= GND
ISO
.
Table 4.
Parameter Symbol Min Typ Max Unit Test Conditions/Comments
DC-TO-DC CONVERTER POWER SUPPLY
Setpoint V
ISO
3.0 3.3 3.6 V I
ISO
= 0 mA
Line Regulation V
ISO(LINE)
1 mV/V I
ISO
= 50 mA, V
DD1
= 4.5 V to 5.5 V
Load Regulation V
ISO(LOAD)
1 5 % I
ISO
= 10 mA to 90 mA
Output Ripple V
ISO(RIP)
50 mV p-p 20 MHz bandwidth, C
BO
= 0.1 μF||10 μF,
I
ISO
= 90 mA
Output Noise V
ISO(N)
130 mV p-p C
BO
= 0.1 μF||10 μF, I
ISO
= 90 mA
Switching Frequency f
OSC
180 MHz
PWM Frequency f
PWM
625 kHz
I
DD1
Supply Current, Full V
ISO
Load I
DD1(MAX)
250 mA
Maximum Output Supply Current I
ISO(MAX)
100 mA V
ISO
> 3.0 V
Efficiency at Maximum Output
Supply Current
26 % I
ISO
= 100 mA
I
DD1
Supply Current, No V
ISO
Load I
DD1(Q)
4 12 mA I
ISO
= 0 mA
Undervoltage Lockout, V
DD1
and V
ISO
Supplies
UVLO
Positive-Going Threshold V
UV+
2.7 V
Negative-Going Threshold V
UV−
2.4 V
Hysteresis V
UVH
0.3 V
PACKAGE CHARACTERISTICS
Table 5.
Parameter Symbol Min Typ Max Unit Test Conditions/Comments
RESISTANCE AND CAPACITANCE
Resistance (Input-to-Output)
1
R
I-O
10
12
Ω
Capacitance (Input-to-Output)
1
C
I-O
2.2 pF f = 1 MHz
Input Capacitance
2
C
I
4.0 pF
IC Junction-to-Ambient Thermal
Resistance
θ
JA
45 °C/W Thermocouple is located at the center of
the package underside; test conducted
on a 4-layer board with thin traces
3
THERMAL SHUTDOWN
Thermal Shutdown Threshold TS
SD
150 °C T
J
rising
Thermal Shutdown Hysteresis TS
SD-HYS
20 °C
1
This device is considered a 2-terminal device; Pin 1 through Pin 8 are shorted together, and Pin 9 through Pin 16 are shorted together.
2
Input capacitance is from any input data pin to ground.
3
Refer to the Thermal Analysis section for thermal model definitions.
Data Sheet ADuM6000
Rev. D | Page 5 of 16
REGULATORY INFORMATION
The ADuM6000 is approved by the organizations listed in Table 6. Refer to Table 11 and the Insulation Lifetime section for more
information about the recommended maximum working voltages for specific cross-isolation waveforms and insulation levels.
Table 6.
UL
1
CSA VDE
2
Recognized under UL 1577
component recognition
program
Approved under CSA Component Acceptance Notice #5A RI-16-2 package:
Certified according to DIN V VDE V
0884-10 (VDE V 0884-10):2006-12
3
Reinforced insulation, 846 V peak
Single protection, 5000 V rms
isolation voltage
Basic insulation per CSA 60950-1-07 and IEC 60950-1, 600 V rms
(848 V peak) maximum working voltage
RW-16 package (pending):
Certified according to IEC 60747-5-2
(VDE 0884 Part 2):2003-01
Basic insulation, 846 V peak
RW-16 package:
Reinforced insulation per CSA 60950-1-07 and IEC 60950-1, 380 V rms
(537 V peak) maximum working voltage
Reinforced insulation per IEC 60601-1, 125 V rms (176 V peak)
maximum working voltage
RI-16-2 package (pending):
Reinforced insulation per CSA 60950-1-07 and IEC 60950-1, 400 V rms
(565 V peak) maximum working voltage
Reinforced insulation per IEC 60601-1, 250 V rms (353 V peak)
maximum working voltage
File E214100 File 205078 File 2471900-4880-0001
1
In accordance with UL 1577, each ADuM6000 is proof-tested by applying an insulation test voltage ≥ 6000 V rms for 1 sec (current leakage detection limit = 15 μA).
2
In accordance with IEC 60747-5-2 (VDE 0884 Part 2):2003-01, each ADuM6000 is proof-tested by applying an insulation test voltage ≥ 1590 V peak for 1 sec (partial
discharge detection limit = 5 pC). The asterisk (*) marking branded on the component designates IEC 60747-5-2 (VDE 0884 Part 2):2003-01 approval.
3
In accordance with DIN V VDE V 0884-10, each ADuM6000 is proof-tested by applying an insulation test voltage ≥1050 V peak for 1 sec (partial discharge detection
limit = 5 pC). The asterisk (*) marking branded on the component designates DIN V VDE V 0884-10 approval.
INSULATION AND SAFETY-RELATED SPECIFICATIONS
Table 7.
Parameter Symbol Value Unit Test Conditions/Comments
Rated Dielectric Insulation Voltage 5000 V rms 1-minute duration
Minimum External Air Gap (Clearance) L(I01) 8.0 mm
Measured from input terminals to output terminals,
shortest distance through air
Minimum External Tracking (Creepage) RW-16
Package
L(I02) 7.6 mm
Measured from input terminals to output terminals,
shortest distance path along body
Minimum External Tracking (Creepage) RI-16-2
Package
L(I02) 8.3 min mm
Measured from input terminals to output terminals,
shortest distance path along body
Minimum Internal Distance (Internal Clearance) 0.017 min mm Distance through insulation
Tracking Resistance (Comparative Tracking Index) CTI >175 V DIN IEC 112/VDE 0303, Part 1
Material Group IIIa Material Group (DIN VDE 0110, 1/89, Table 1)
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P17

ADUM6000ARIZ-RL

Mfr. #:
Buy ADUM6000ARIZ-RL
Manufacturer:
Analog Devices / Linear Technology
Description:
Switching Voltage Regulators 5kV DC/DC Converter
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet