1/21
www.rohm.com
2010.06 - Rev.A
© 2010 ROHM Co., Ltd. All rights reserved.
Small-sized Class-D Speaker Amplifiers
Analog Input
Stereo Class-D Speaker Amplifier
BD5471MUV
Description
BD5471MUV is a low voltage drive class-D stereo speaker amplifier that was developed for note-book PC, cellular phone,
mobile audio products and the others. LC filters of speaker outputs are unnecessary, and only 7 external components are
needed for speaker system. Also, 3.3V regulator in BD5471MUV can use power supply for audio-codec. BD5471MUV, that
is high-efficiency, low consumption, is suitable for application by using battery. Shutdown current is 0µA typically. Also,
start-up time is fast from shutdown to active mode. BD5471MUV can use for some applications that change mode between
“shutdown state” and “active state”.
Features
1) High power 2.3W typ. (VDD=5V, RL=4, THD+N=10%, stereo input)
High power 1.5W typ. (VDD=5V, RL=8, THD+N=10%, stereo input)
2) Gain selectable by the external control (6, 12, 18, 24dB)
3) Pop noise suppression circuitry
4) Standby function (Mute function) [I
SD
=0uA]
5) Protection circuitry (Short protection [Audio, REG], Thermal shutdown, Under voltage lockout)
6) Built-in 3.3V regulator
7) Built-in BEEP detect circuitry
8) Very small package VQFN024V4040
Applications
Notebook computers,Mobile electronic applications,Mobile phones,PDA etc.
Absolute Maximum Ratings(Ta=+25)
Parameter Symbol Ratings Unit
Power Supply Voltage VDD 7.0 V
Power Dissipation Pd
0.7 *1 W
2.2 *2 W
Storage Temperature Range Tstg -55 ~ +150
Input Voltage Range *3 Vin -0.3 ~ VDD+0.3 V
Control Terminal
Input Voltage Range *4
Vctl -0.3 ~ VDD+0.3 V
*1 74.2mm×74.2mm×1.6mm, FR4 1-layer glass epoxy board(Copper on top layer 0%)
Derating in done at 5.6mW/ for operating above Ta=25. There are thermal via on the board
*2 4.2mm×74.2mm×1.6mm, FR4 4-layer glass epoxy board (Copper on bottom 2 and 3 layer 100%)
*3 input Terminal (INL+, INL-, INR+, INR-)
*4 Control Terminal (MUTE, G0, G1, EAPD, BEEP, REG_SD)
Operating Conditions
Parameter Symbol Ratings Unit
Power Supply Voltage
VDD +4.5 ~ +5.5 V
Temperature Range
Topr -40 ~ +85
* These products aren’t designed for protection against radioactive rays.
No.10101EAT03
Technical Note
2/21
BD5471MUV
www.rohm.com
2010.06 - Rev.A
© 2010 ROHM Co., Ltd. All rights reserved.
Electric Characteristics(Unless otherwise specified, Ta=+25, VDD=+5.0V, RL=8Ω, AC item= LC Filter(L=22µH, C=1µF) )
Parameter Symbol
Limits
Unit Conditions
MIN. TYP. MAX.
Circuit current (Active)
I
CC
5.5 12.0 mA
Active mode,
MUTE=H, EAPD=H, No load
Circuit current (Standby)
I
STBY
0.1 1.0 mA Standby mode, MUTE=H,EAPD=L
Circuit current (Regulator)
I
CCR
0.15 1.0 mA
Regulator Mode, MUTE=EAPD=L
REG_SD=H
Circuit current (Shutdown)
I
SD
0.1 2.0 µA
Shutdown mode, MUTE=L,
REG_SD=L
<Speaker Amplifier>
Output power 1 P
O1
0.8 1.2 W
BTL, f=1kHz, THD+N=1%,
Stereo input, *1, *2
Output power 2 P
O2
1.0 1.5 W
BTL, f=1kHz, THD+N=10%,
Stereo input, *1, *2
Voltage gain GV
5.5 6.0 6.5 dB BTL, G0=G1=GND
11.5 12 12.5 dB BTL, G0=GND, G1=VDD
17.5 18 18.5 dB BTL, G0=VDD, G1=GND
23.5 24 24.5 dB BTL, G0=G1=VDD
Total harmonic distortion THD+N 0.2 1.0 % BTL, Po=0.7*P
O1
*1, *2
Crosstalk C
T
60 70 dB BTL, f=1kHz *1, *3
S/N SNR 70 90 dB BTL, Po=P
O1
*1, *3
Switching Frequency fosc 175 250 325 kHz
Start-up time Ton 0.78 1.02 1.46 msec
Input resistance R
IN
63 90 117 kΩ G0=G1=GND
42 60 78 kΩ G0=GND, G1=VDD
25 36 47 kΩ G0=VDD, G1=GND
14 20 26 kΩ G0=G1=VDD
<Regulator>
Output voltage Vo 3.15 3.30 3.45 V Io=150mA
Maximum output current Iom 150 200 mA Vo=3.15V
Load regulation L
REG
0.2 1 mV/mA Io=0150mA
<Control terminal (MUTE, G0, G1, EAPD, BEEP, REG_SD) >
Control terminal
input voltage
High-level
V
CTLH
1.4 VDD V
Low-level
V
CTLL
0 0.4 V
Control terminal input current
I
CTL
22 33 44 µA
Control terminal Input voltage
V
CTL
=5V
*1: B.W.=400 ~ 30kHz, BTL:The voltage between 3pin and 6pin, 13pin and 16pin
Active / Standby Control
Mode Pin level Conditions
MUTE H/L IC active/ shutdown
EAPD H/L IC active/standby
BEEP H/L IC active/standby
REG_SD H/L REG active/shutdown
Technical Note
3/21
BD5471MUV
www.rohm.com
2010.06 - Rev.A
© 2010 ROHM Co., Ltd. All rights reserved.
G0
G0
150k
G1
BEEP
DET
INR
24 19202122
23
INL- INR
AVDD
A
GNDINL+
C6
7 8 9 10 11
12
REG_OU
MUTE EAP REG_S
REG_VD
REG
_
GN
C2
2
.
2
μ
F
C3
SHORT
SHORT
EAPD
3.3VRE
PWM
Gain
Select
H-
Bridge
BEEP
PWM
Gain
Select
H-
Bridg
STOP
UVLO TSD SHOR
BIAS
OSC
BEE
P
MUT
E
EAPD
UVLO
T
S
D
MUT
E
150k
G1 G1
G0
1
2
3
4
5
6
BEEP
DET_C
OUTL
PVDD
OUTL-
PGNDL
C1
0.01u
F
VDD
13
14
15
16
17
18
PVDD
OUTR-
PGND
OUTR
G1
G0
C
8
0.1μ F
C7
0.1μF
C9
10u
F
C5
0.1μF
C4
0.1μF
1μ F
8
VDD
VDD
150k
150k
+B
150k
SHORT
SHORT
SHORT
SHORT
UVLO
T
S
D
V
V
V
22μF
1μF
22μF
A
A
V
SE
V
SE
V
BTL
V
BEEP
V
MUTE
A
V
EAPD
A
V
REG_
SD
Vin Vin Vin Vin
A
V
G0
A
V
G1
8
V
BTL
V
V
V
1μF
1μF
22μF
22μF
V
SE
V
SE
Measurement Circuit Diagram
Package Outlines
VQFN024V4040 (Plastic Mold)
(Unit: mm)
Bottom View Top View
D5471

640501-4

Mfr. #:
Manufacturer:
TE Connectivity / AMP Connectors
Description:
Headers & Wire Housings 9CKT DUPLEX .120
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet