DO NOT
SCALE FROM
THIS PRINT
.045
1.14
SQ REF
.100
REF
2.54
"B"
(SEE NOTE 2)
2
MAX SWAY
(EITHER DIRECTION)
T-1S8-XX-XX
C1
(No OF POS X .20[5.1])
.250
REF
6.35
(No OF POS-1)X.200[5.08]
.100
REF
2.54
.125
REF
3.18
W
W
"E"
.200 5.08
.04 1.02
90°
-
0°
+
4°
-VS: SURFACE MOUNT
-01 & -02 ONLY
C2
SEE NOTE 10
"A"
(SEE NOTE 4 & 6 FOR
-05 LEAD STYLE)
2
MAX SWAY
(EITHER DIRECTION)
-S: SINGLE
"D"
REF
90°
"C"
-RA: RIGHT ANGLE
-02 & -04 ONLY
No OF POSITIONS
-01 THRU -20
ROW SPECIFICATION
-S: SINGLE
SEE TABLE 2
LEAD STYLE
SEE TABLE 1
OPTION
HPM-XX-XX-XX-X-XX-X
PLATING SPECIFICATIONS
OPTION
-P: PICK PLACE PAD
(USE PPP-47)
(-VS ONLY, 3 POS MIN,
NOT AVAILABLE IN -05
LEAD STYLE)
-T:
MATTE TIN CONTACT
AND TAIL
-TM:
MATTE TIN CONTACT
AND TAIL
-RA: RIGHT ANGLE POST
(-02 & -04 LEAD STYLE ONLY)
-VS: VERTICAL SURFACE MOUNT
(-01 & -02 LEAD STYLE ONLY)
(2 POSITION MINIMUM)
C
TABLE 2
FORM
BODY
MATERIAL
T/H
FSW-20-200
BLACK, PBT,
UL 94 VO
RA
FSW-20-200
VS
HFSW-20-200
NATURAL, LCP,
UL 94 VO
TABLE 1
STYLE
TERMINAL
"A"
"B"
"C"
"D"
"E"
-01
T-1S8-11-TX
.180[4.57]
.470[11.94]
N/A N/A
.422[10.72]
-02
T-1S8-12-TX
.180[4.57]
.520[13.21]
.100[2.54] .175[4.45]
.482[12.24]
-04
T-1S8-14-TX
.161[4.09]
.829[21.06]
.195[4.95] .156[3.96]
N/A
-05
T-1S8-11-TX
.180[4.57] .150[3.81]
N/A N/A N/A
-06
T-1S8-15-TX
.180[4.57]
1.070[27.18]
N/A N/A N/A
SHEET OF
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS ANGLES
.XX:
.01 [.3] 2
.XXX:
.005 [.13]
.XXXX:
.0020 [.051]
MATERIAL:
.200 HIGH POWER BLOCK, ASM
BY:
HPM-XX-XX-XX-X-XX-X
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
BURRES
08/21/98
2
1
SHEET SCALE: 1:1
F:\DWG\MISC\MKTG\HPM-XX-XX-XX-X-XX-X-MKT.SLDDRW
NOTES:
1. REPRESENTS A CRITICAL DIMENSION.
2. MAXIMUM HEIGHT VARIATION BETWEEN ANY TWO PINS: .005[.13]
3. MAXIMUM PIN ROTATION IN BODY: 2°
4. TAILS TO BE SHEARED TO ACHIEVE DIMENSIONAL CALLOUT ±.010[.25]
5. MINIMUM PUSHOUT FORCE: 3 LBS.
6. MAXIMUM ALLOWABLE BURR: .0015[.038]
7. THROUGH HOLES (-S & -RA) ARE TO BE BULK PACKAGED.
8. SURFACE MOUNT (-VS) IS TO BE PACKAGED AS FOLLOWS:
POSITIONS -04 THRU -20 ARE TO BE TUBE PACKAGED;
POSITION -02 TO BE LAYER PACKAGED,
-03 POSITION TO BE TUBE OR LAYER PACKAGED.
9. MAXIMUM CUT FLASH: .020[.51]
10. COPLANARITY (-VS); POSITIONS -02 THRU -15: .008[.20],
POSITIONS -16 THRU -20: .010[.25]
BODY: SEE TABLE 2
TERMINAL: CDA7025
GRADE TL02
MAX BOW ALLOWED: .003 IN/IN
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
REVISION W
