OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

1-2029098-4

P1-P3P4-P6P7-P8
1 of 8
© 2016 TE Connectivity family of companies
All Rights Reserved
| Indicates Change
*Trademark. TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.
Product
Specification
This controlled document is subject to change.
For latest revision and Regional Customer Service, visit our website at www.te.com
PRODUCT INFORMATION 1-800-522-6752
108-2112
28 SEP 2016 Rev D2
VAL-U-LOK* Connectors
1. SCOPE
1.1. Content
This specification covers performance, tests and quality requirements for VAL-U-LOK* Connectors.
1.2. Qualification
When tests are performed on the subject product line, procedures specified in Figure 1 shall be used. All
inspections shall be performed using the applicable inspection plan and product drawing.
1.3. Successful qualification testing on the subject product line was completed on 25Jul03. The Qualification
Test Report number for this testing is
501-534. This documentation is on file at and available from
Engineering Practices and Standards (EPS).
2. APPLICABLE DOCUMENTS
The following documents form a part of this specification to the extent specified herein. Unless otherwise
specified, the latest edition of the document applies. In the event of conflict between the requirements of
this specification and the product drawing, the product drawing shall take precedence. In the event of
conflict between the requirements of this specification and the referenced documents, this specification
shall take precedence.
2.1. TE Connectivity (TE) Documents
114-13172: Application Specification (VAL-U-LOK* Series Headers and Connectors)
501-534: Qualification Test Report (VAL-U-LOK* Connector)
2.2. Industry Document
EIA-364: Electrical Connector/Socket Test Procedures Including Environmental Classifications
2.3. Reference Document
109-197: Test Specification (Tyco Electronics Test Specifications vs EIA and IEC Test Methods)
3. REQUIREMENTS
3.1. Design and Construction
Product shall be of the design, construction and physical dimensions specified on the applicable product
drawing.
3.2. Materials
Materials used in the construction of this product shall be as specified on the applicable product
drawing.
3.3. VDE Agency Approval details:
TE Manufacturing location code: T007 (mark of origin for company 5011703, Chaogui Science and
Technology (Shenzhen) Co. Ltd.)
108-2112
Rev D2
2 of 8
3.4. Ratings
Voltage: 600 volts AC
Current: 9 amperes maximum, 2 position application
Temperature: -40 to 105°C
3.5. Performance and Test Description
Product is designed to meet the electrical, mechanical and environmental performance requirements
specified in Figure 1. Unless otherwise specified, all tests shall be performed at ambient environmental
conditions.
3.6. Test Requirements and Procedures Summary
Test Description
Requirement
Procedure
Initial examination of product.
Meets requirements of product
drawing and Application
Specification
114-13172.
Visual and dimensional (C of C)
inspection per product drawing.
Final examination of product.
Meets visual requirements.
Visual inspection.
ELECTRICAL
Low Level Contact Resistance
(LLCR).
10 milliohms maximum.
Subject specimens to 100
milliamperes maximum and 20
millivolts maximum open circuit
voltage.
Insulation resistance.
1000 megohms minimum.
500 volts DC, 2 minute hold.
Test between adjacent contacts.
Withstanding voltage.
One minute hold with no breakdown
or flashover.
1500 volts AC at sea level.
Test between adjacent contacts.
Temperature rise vs current.
30°C maximum temperature rise at
specified current.
See Figure 3 for Rating Curves on
#18 AWG lead wire.
Stabilize at a single current level
until 3 readings at 5 minute
intervals are within 1°C
MECHANICAL
Sinusoidal vibration.
No discontinuities of 1 microsecond
or longer duration.
See Note.
Subject mated specimens to 10 to
55 to 10 Hz traversed in 1 minute
with 1.5 mm maximum total
excursion. Two hours in each of 3
mutually perpendicular planes.
Mechanical shock.
No discontinuities of 1 microsecond
or longer duration.
See Note.
Subject mated specimens to 50 G's
half-sine shock pulses of 11
milliseconds duration. Three shocks
in each direction applied along 3
mutually perpendicular planes, 18
total shocks.
Figure 1 (cont’d)
108-2112
Rev D2
3 of 8
Test Description
Requirement
Procedure
Durability.
See Note.
Mate and unmate specimens with
H-04 hardness for 50 cycles, and
specimens with H-06 hardness for
30 cycles at a maximum rate of 10
cycles per minute.
Crimp pull-out force.
88 N minimum for 16 AWG wire;
88 N minimum for 18 AWG wire;
59 N minimum for 20 AWG wire;
39 N minimum for 22 AWG wire;
29 N minimum for 24 AWG wire;
20 N minimum for 26 AWG wire.
Measure force necessary to remove
the wire from the crimp at a
maximum rate of 12.7 mm per
minute.
Locking force.
41.2 N maximum for 6 position.
Measure force necessary to mate
specimens at a maximum rate of
12.7 mm per minute.
Unlocking force.
2.4 N minimum for 6 position.
Measure force necessary to unmate
specimens at a maximum rate of
12.7 mm per minute.
Terminal insertion.
15 N maximum.
Measure force necessary to
properly seat the terminal into the
housing at a maximum rate of 12.7
mm per minute.
Terminal retention.
30 N minimum.
Measure force necessary to remove
the terminal from the housing at a
maximum rate of 12.7 mm per
minute.
ENVIRONMENTAL
Thermal shock.
See Note.
Subject mated specimens to 5
cycles between -55 and 105°C with
30 minute dwells at temperature
extremes and 1 minute transition
between temperatures.
Humidity, steady state.
See Note.
Subject specimens to 40°C and 90
to 95% RH for 96 hours.
Heat resistance.
See Note.
Subject mated specimens to 105°C
for 96 hours.
Cold resistance.
See Note.
Subject mated specimens to -40°C
for 96 hours.
Figure 1 (cont’d)
P1-P3P4-P6P7-P8

1-2029098-4

Mfr. #:
Buy 1-2029098-4
Manufacturer:
TE Connectivity / AMP Connectors
Description:
Headers & Wire Housings 14 POS PLUG PNL MNT UL-94-V0 BLUE
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet