LPS255-C Datasheet 70-841-005, LPS252-C, LPS254-CEF | P1-P3

POWER

LPS250 Series

250 Watts

Total Power: 250 Watts

Input Voltage: 85 - 264 Vac

120 - 300 Vdc

# of Outputs: Single

SPECIAL FEATURES

 Active power factor correction

 IEC EN6100-3-2 compliance

 Remote sense & remote inhibit

 Power fail

 Single wire current sharing

 Built-in EMI lter

 2:1 Wide range output voltage adjust

 2 Supervisory outputs 5 V and 12 V

 Overvoltage protection

 Overload protection

 Thermal overload protection

 DC power good

 120 kHz switching frequency

 RoHS compliant

 Cover -C

 Optional top with fan cover -CF

 Optional end fan cover -CEF

SAFETY

 VDE 60950

 UL 60950

 CSA 60950

 NEMKO 60950

 CB Certicate and report 2186

 CE Mark (LVD)

Electrical Specications

Input

Input range 85 - 264 Vac; 120 - 300 Vdc

Frequency 47 - 440 Hz

Inrush current 20 A max, cold start @ 25 °C

Efciency 75% typical at full load

EMI lter FCC Class B conducted and radiated

CISPR 22 Class B conducted and radiated

EN55022 Class B conducted and radiated

VDE 0878 PT3 Class B conducted and radiated

Safety ground leakage current < 0.5 mA @ 50/60 Hz, 264 Vac input

Output

Maximum power With cover: 250 W with 30 CFM forced air.

(-C) (-CF) (CEF)

Supervisory output 5 V @ 100 mA regulated; 12 V @ 500 mA

Adjustment range 2:1 wide ratio

Hold-up time 20 ms @ 250 W load, 115 VAC nominal line

Overload protection Short circuit protection on all outputs. Case overload protected @

10 - 145% above peak rating

Overvoltage protection 5 V output: 5.7 to 6.7 Vdc.

Other models 10% to 25% above nominal output

Logical Control

Power failure TTL Logic signal goes high 50 - 150 msec after 5 V output. It goes low at

least 4 ms before loss of regulation

Remote on/off Requires an external contact (N.O or N.C) to inhibit outputs

DC - OK TTL logic goes high 50 - 150 msec after the output. It goes low when there

is loss of regulation.

Remote sense Compensates for 0.5 V lead drop minimum, will operate without remote

sense connected. Reverse connection protected

Data Sheet

LPS250 Series Data Sheet

Ordering Information

Model

Number

Output

Voltage

Minimum

Load

Maximum Load with

30CFM Forced Air

Peak Load

Regulation

Ripple

P/P (PARD)

LPS252-C 5 V (3 - 6 V) 1.50 A 50 A 60 A ±2% 50 mV

LPS253-C 12 V (6 - 12 V) 0.63 A 21 A 25 A ±2% 120 mV

LPS254-C 15 (12 - 24 V) 0.50 A 16.7 A 20 A ±2% 150 mV

LPS255-C 24 V (24 - 48 V) 0.32 A 10.4 A 12.5 A ±2% 240 mV

1. Peak current lasting < 30 seconds with a maximum 10% duty cycle.

2. At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings.

3. Peak-to-peak with 20 MHz bandwidth and 10 μF in parallel with a 0.1 μF capacitor at rated line voltage and load ranges.

4. If optional CF or CEF fans are not used, 30CFM forced air cooling needs to be provided and is required through the length of the

power supply. Not convection rated.

5. Output voltage adjustment requires a minimum load.

6. Remote inhibit resets OVP latch

7. This product is a Component Power Supply and is only for inclusion by professional installers within other equipment and must not be

operated as a standalone product. EMC compliance to appropriate standards must be veried at the system level. This product is for sale

to OEMs and System Integrators, including through Distribution Channels. It is not intended for sale to End Users.

Note: -CF sufx added to the model number indicates cover with top fan. -CEF sufx added to the model number indicates cover with dual end mounted fan cover and AC inlet.

Environmental Specications

Operating temperature 0° to 50 °C ambient; derate each output at 2.5% per degree from 50° to 70 °C

Storage temperature -40 °C to +85 °C

Temperature coefcient ± 0.4% per °C

Electromagnetic susceptibility Designed to meet IEC 801, -2, -3, -4, -5, -6, Level 3

Humidity Operating; non-condensing 5% to 95%

Vibration Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.7 G peak 5 Hz to

500 Hz, operational

MTBF demonstrated > 550,000 hours at full load and 25 °C ambient conditions

LPS250 Series Data Sheet

WORLDWIDE OFFICES

Americas

2900 S.Diablo Way

Tempe, AZ 85282

USA

+1 888 412 7832

Europe (UK)

Waterfront Business Park

Merry Hill, Dudley

West Midlands, DY5 1LX

United Kingdom

+44 (0) 1384 842 211

Asia (HK)

14/F, Lu Plaza

2 Wing Yip Street

Kwun Tong, Kowloon

Hong Kong

+852 2176 3333

For more information: www.artesyn.com/power

For support: productsupport.ep@artesyn.com

Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and

service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade

www.artesyn.com

LPS250 DS 18Mar2016

Mechanical Drawing

5.0 (127.0)

2.0

(50.8)

1.18 (30.0)

9.0

(228.6)

6.64

(168.6)

3.42 (87.0)

.79

(20)

SK3

SK1

12345678

3 2 1

SK5

+ve -ve

Terminal

Block TB1

O/P ADJ.

SK4

FAN

#6-32 (4 places)

5.46

(138.6)

8.52

(216.4)

M3 (4 places)

3.68

(93.6)

3.15

(80)

2.17

(55)

3.0

(76.2)

.55

(14)

1.30

(33.0)

Optional

(-CF)

Cover

with Fan

Optional

(-CEF)

Cover

with fans

10.32

(262.0)

SK7

FAN

AC Inlet

10.0

#6-32

Optional

(-CEF)

Cover

with fans

Optional

(-CF)

Cover

with Fan

.24 (6.1)

6-32 (2 places)

Main Output

6-32 (3 places)

Pin Assignments

Connector

SK1 PIN 1 Neutral

PIN 2 Line

PIN 3 Ground

SK3 PIN 1 + Remote sense

PIN 2 - Remote sense

PIN 3 Remote inhibit (N.O.)

PIN 4 Remote inhibit (N.C.)

PIN 5 Common

PIN 6 Current sharing

PIN 7 Power fail

PIN 8 DC Power Good

SK4 PIN 1 + Fan’s power source (12 V @ 500 mA)

PIN 2 - Fan’s power source (12 V @ 500 mA)

SK5 PIN 1 + Supervisory output supply (5 V @ 100 mA)

PIN 2 - Supervisory output supply (5 V @ 100 mA)

SK7 PIN 1 + Fan’s power source (12 V @ 500 mA)

PIN 2 - Fan’s power source (12 V @ 500 mA)

Mating Connectors

SK3 Molex 22-01-1084

PINS:08-70-0057

SK4 Molex 22-01-3027

PINS: 08-50-0114

SK5 Molex 22-01-3027

PINS: 08-50-0114

SK7 Molex 22-01-3027

PINS: 08-50-0114

Artesyn Embedded Technologies Connector Kit #70-841-005, includes all of the above

1. Specications subject to change without notice.

2. All dimensions in inches (mm), tolerance is ± 0.02”(± 0.5 mm)

3. Specications are at factory settings.

4. To enable normally closed remote inhibit, cut jumper J1.

5. Mounting maximum insertion depth is 0.12”.

6. Warranty: 2 year

7. Weight: 2.6 lb / 1.19 kg

P1-P3

LPS255-C

Mfr. #:

Buy LPS255-C

Manufacturer:

Description:

Switching Power Supplies 24v-48v output 250W 5"x9" w/cove

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

LPS255-C

LPS255-C

Products related to this Datasheet