OMO ElectronicOMO Electronic
Expand menu
0 Cart

PC81510NSZ

P1-P3P4-P6P7-P9P10-P11
Sheet No.: D2-A03901EN
7
10 20 30 40−20−10 0 50 60 70 80 90 100
Collector dark current I
CEO
(A)
Ambient temperature T
a
(˚C)
−30
10
−10
10
−9
10
−8
10
−7
10
−6
10
−5
10
−4
V
CE
=10V
Fig.13 Collector Dark Current vs. Ambient
Temperature
Fig.15 Test Circuit for Response Time
0.01
0.1 1
1 000
10
1
100
10
Response time (µs)
t
s
t
d
t
f
t
r
Load resistance R
L
(kΩ)
V
CE
=2V
I
C
=10mA
T
a
=25˚C
Fig.14 Response Time vs. Load Resistance
Remarks : Please be aware that all data in the graph are just for reference and not for guarantee.
PC81510NSZ
V
CC
t
f
t
r
t
s
90%
10%
t
d
Output
Input
R
L
Input OutputR
D
Please refer to the conditions in Fig.14.
V
CE
Sheet No.: D2-A03901EN
■ Design Considerations
While operating at I
F
<0.5mA, CTR variation may increase.
Please make design considering this fact.
This product is not designed against irradiation and incorporates non-coherent IRED.
● Degradation
In general, the emission of the IRED used in photocouplers will degrade over time.
In the case of long term operation, please take the general IRED degradation (50% degradation over 5years)
into the design consideration.
8
● Design guide
PC81510NSZ
Sheet No.: D2-A03901EN
■ Manufacturing Guidelines
● Soldering Method
Flow Soldering :
Due to SHARP's double transfer mold construction submersion in flow solder bath is allowed under the below
listed guidelines.
Flow soldering should be completed below 270˚C and within 10s.
Preheating is within the bounds of 100 to 150˚C and 30 to 80s.
Please don't solder more than twice.
Hand soldering
Hand soldering should be completed within 3s when the point of solder iron is below 400˚C.
Please don't solder more than twice.
Other notices
Please test the soldering method in actual condition and make sure the soldering works fine, since the impact
on the junction between the device and PCB varies depending on the tooling and soldering conditions.
9
PC81510NSZ
Solvent cleaning:
Solvent temperature should be 45ºC or below Immersion time should be 3minutes or less
Ultrasonic cleaning:
The impact on the device varies depending on the size of the cleaning bath, ultrasonic output, cleaning time,
size of PCB and mounting method of the device.
Therefore, please make sure the device withstands the ultrasonic cleaning in actual conditions in advance of
mass production.
Recommended solvent materials:
Ethyl alcohol, Methyl alcohol and Isopropyl alcohol
In case the other type of solvent materials are intended to be used, please make sure they work fine in ac-
tual using conditions since some materials may erode the packaging resin.
● Cleaning instructions
This product shall not contain the following materials.
And they are not used in the production process for this device.
Regulation substances:CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform)
Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all.
● Presence of ODC
P1-P3P4-P6P7-P9P10-P11

PC81510NSZ

Mfr. #:
Buy PC81510NSZ
Manufacturer:
Sharp Microelectronics
Description:
OPTOISOLATOR 5KV DARL 4DIP
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet