98
030917
F91-AJ6 Series
Low ESR, Resin-Molded Chip - Automotive Product Range
Capacitance Rated Voltage
µF Code 6.3V (0J) 10V (1A) 16V (1C)
10 106 A A
22 226 A A B
33 336 A B B
47 476 B B
100 107 N
CAPACITANCE AND RATED VOLTAGE
RANGE (LETTER DENOTES CASE SIZE)
Available Ratings
RATINGS & PART NUMBER REFERENCE
AVX Case Capacitance
Rated
DCL
DF ESR
100kHz RMS
*1
Part No. Size (μF)
Voltage @ 120Hz @ 100kHz
Current
ΔC/C
(V)
(μA)
(%) (mΩ)
(mA)
(%)
20°C
6.3 Volt
F910J226MAAAJ6 A 22 6.3 1.4 8 1250 245 *
F910J336MAAAJ6 A 33 6.3 2.1 8 1250 245 *
F910J476MBAAJ6 B 47 6.3 3.0 6 500 412 *
10 Volt
F911A106MAAAJ6 A 10 10 1.0 6 1500 224 *
F911A226MAAAJ6 A 22 10 2.2 12 1250 245 *
F911A336MBAAJ6 B 33 10 3.3 8 700 348 *
F911A476MBAAJ6
B
47 10 4.7 8 500 412 *
16 Volt
F911C106MAAAJ6 A 10 16 1.6 6 1500 224 *
F911C226MBAAJ6
B
22 16 3.5 8 950 299 *
F911C336MBAAJ6
B
33 16 5.3 8 950 299 *
F911C107MNCAJ6 N 100 16 16.0 10 100 1225 *
TEST
F91-AJ6 series (Temperature range -55ºC to +125ºC)
Condition
At 40°C, 90 to 95% R.H., 500 hours (No voltage applied)
Damp Heat Capacitance Change ........... Refer to above (*1)
(Steady State) Dissipation Factor ................ Initial specified value or less
Leakage Current .................. Initial specified value or less
After 1000 hour’s application of rated voltage in series with a 33Ω resistor at 85°C, 85% R.H.,
capacitors meet the characteristics requirements table below.
Load Humidity Capacitance Change ........... Refer to above (*1)
Dissipation Factor ................ Initial specified value or less
Leakage Current .................. 125% or less than the initial specified value
At -55°C / +125°C, 30 minutes each, 1000 cycles
Temperature Cycles
Capacitance Change ........... Refer to above (*1)
Dissipation Factor ................ Initial specified value or less
Leakage Current .................. Initial specified value or less
10 seconds reflow at 260°C, 10 seconds immersion at 260°C.
Resistance to Capacitance Change ........... Refer to above (*1)
Soldering Heat Dissipation Factor ................ Initial specified value or less
Leakage Current .................. Initial specified value or less
After application of surge voltage in series with a 33Ω resistor at the rate of 30 seconds ON, 30 seconds OFF,
for 1000 successive test cycles at 85ºC, capacitors shall meet the characteristic requirements in the table above.
Surge Capacitance Change ........... Refer to above (*1)
Dissipation Factor ................ Initial specified value or less
Leakage Current .................. Initial specified value or less
After 2000 hours’ application of rated voltage in series with a 3Ω resistor at 85°C, or derated voltage in series
with a 3Ω resistor at 125°C, capacitors shall meet the characteristic requirements in the table above.
Endurance Capacitance Change ........... Refer to above (*1)
Dissipation Factor ................ Initial specified value or less
Leakage Current .................. Initial specified value or less
Shear Test
After applying the pressure load of 17.7N for 60 seconds horizontally to the center of capacitor side
body which has no electrode and has been soldered beforehand on a substrate, there shall be found
neither exfoliation nor its sign at the terminal electrode.
Terminal Strength
Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at
both of the opposite bottom points 45mm apart from the center of capacitor, the pressure strength is
applied with a specified jig at the center of the substrate so that substrate may bend by1mm as
illustrated. Then, there shall be found no remarkable abnormality on the capacitor terminals.
Failure Rate
1% per 1000 hours at 85°C, V
R
with 0.1Ω/V series impedance,
60% confidence level.
QUALIFICATION TABLE
Item All Case (%)
Damp Heat ±10
Temperature cycles ±10
Resistance soldering heat ±10
Surge ±10
Endurance ±10
* In case of capacitance tolerance ± 10% type, “K” will be put at 9th digit of type numbering system
*1: ΔC/C Marked “*”
