OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

DLP-2232MSP

P1-P3P4-P6P7-P9P10-P12P13-P13
Rev. 1.1 (May 2011) 10 © DLP Design, Inc.
13
P1.1 (I/O) Port 1 Pin 1 connected to the MSP430F2618 Digital I/O P1.1
14
P2.0 (I/O) Port 2 Pin 0 connected to the MSP430F2618 Digital I/O P2.0
15
P2.6 (I/O) Port 2 Pin 6 connected to the MSP430F2618 Digital I/O P2.6
16
P2.1 (I/O) Port 2 Pin 1 connected to the MSP430F2618 Digital I/O P2.1
17
P2.5 (I/O) Port 2 Pin 5 connected to the MSP430F2618 Digital I/O P2.5
18
P2.2 (I/O) Port 2 Pin 2 connected to the MSP430F2618 Digital I/O P2.2
19
P2.4 (I/O) Port 2 Pin 4 connected to the MSP430F2618 Digital I/O P2.4
20
P2.3 (I/O) Port 2 Pin 3 connected to the MSP430F2618 Digital I/O P2.3
21
P2.7 (I/O) Port 2 Pin 7 connected to the MSP430F2618 Digital I/O P2.7
22
SWVCC (Out) Power from EXTVCC (Pin 24) controlled via Pin 60 (PWREN#) of the
FT2232H and Q1 MOSFET power switch; R8 and C24 control the power-up rate to help
limit inrush current
23 GROUND
24
EXTVCC (In) Use for applying main power (4.4-5.25 volts) to the module; connect to
PORTVCC if the module is to be powered by the USB port (typical configuration)
25
PORTVCC (Out) Power from USB port—Connect to EXTVCC if the module is to be
powered by the USB port (typical configuration); 500mA is the maximum current
available to the DLP-2232MSP and target electronics if the USB device is configured for
high power
26 GROUND
27
DB0 (I/O) Line 0 of the data bus between the MSP430F2618 and the FT2232H USB-
FIFO
28
DB1 (I/O) Line 1 of the data bus between the MSP430F2618 and the FT2232H USB-
FIFO
29
DB2 (I/O) Line 2 of the data bus between the MSP430F2618 and the FT2232H USB-
FIFO
30
DB3 (I/O) Line 3 of the data bus between the MSP430F2618 and the FT2232H USB-
FIFO
31
DB4 (I/O) Line 4 of the data bus between the MSP430F2618 and the FT2232H USB-
FIFO
32
DB5 (I/O) Line 5 of the data bus between the MSP430F2618 and the FT2232H USB-
FIFO
33
DB6 (I/O) Line 6 of the data bus between the MSP430F2618 and the FT2232H USB-
FIFO
34
DB7 (I/O) Line 7 of the data bus between the MSP430F2618 and the FT2232H USB-
FIFO
35 GROUND
36
P3.4 (I/O) Port 3 Pin 4 connected to the MSP430F2618 Digital I/O P3.4
37
P3.2 (I/O) Port 3 Pin 2 connected to the MSP430F2618 Digital I/O P3.2
38
P3.3 (I/O) Port 3 Pin 3 connected to the MSP430F2618 Digital I/O P3.3
39
P3.0 (I/O) Port 3 Pin 0 connected to the MSP430F2618 Digital I/O P3.0
40
P3.5 (I/O) Port 3 Pin 5 connected to the MSP430F2618 Digital I/O P3.5
41
P3.1 (I/O) Port 3 Pin 1 connected to the MSP430F2618 Digital I/O P3.1
42 GROUND
43
P5.0 (I/O) Port 5 Pin 0 connected to the MSP430F2618 Digital I/O P5.0
44
P5.2 (I/O) Port 5 Pin 2 connected to the MSP430F2618 Digital I/O P5.2
45
P5.1 (I/O) Port 5 Pin 1 connected to the MSP430F2618 Digital I/O P5.1
46
P5.3 (I/O) Port 5 Pin 3 connected to the MSP430F2618 Digital I/O P5.3
47
P5.4 (I/O) Port 5 Pin 4 connected to the MSP430F2618 Digital I/O P5.4
48
P5.5 (I/O) Port 5 Pin 5 connected to the MSP430F2618 Digital I/O P5.5
Rev. 1.1 (May 2011) 11 © DLP Design, Inc.
49
P5.7 (I/O) Port 5 Pin 7 connected to the MSP430F2618 Digital I/O P5.7
50
P5.6 (I/O) Port 5 Pin 6 connected to the MSP430F2618 Digital I/O P5.6
6.0 MECHANICAL DRAWINGS (PRELIMINARY) INCHES (MILLIMETERS)
UNLESS OTHERWISE NOTED
Rev. 1.1 (May 2011) 12 © DLP Design, Inc.
7.0 DISCLAIMER
Neither the whole nor any part of the information contained within or the product described in this
datasheet may be adapted or reproduced in any material or electronic form without the prior written
consent of the copyright holder.
This product and its documentation are supplied on an as-is basis, and no warranty as to their
suitability for any particular purpose is either made or implied. DLP Design will not accept any claim
for damages whatsoever arising as a result of use or failure of this product. Your statutory rights are
not affected.
This product or any variant of it is not intended for use in any medical appliance, device or system in
which the failure of the product might reasonably be expected to result in personal injury.
This document provides preliminary information that may be subject to change without notice.
8.0 CONTACT INFORMATION
DLP Design, Inc.
1605 Roma Lane
Allen, TX 75013
Phone: 469-964-8027
Fax: 415-901-4859
Email: support@dlpdesign.com
Internet: http://www.dlpdesign.com
P1-P3P4-P6P7-P9P10-P12P13-P13

DLP-2232MSP

Mfr. #:
Buy DLP-2232MSP
Manufacturer:
DLP Design
Description:
Interface Development Tools USB to MSP430 w/ FTDI FT2232H
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet