LTC6084/LTC6085
5
60845fa
The l denotes the specifi cations which apply over the full operating
temperature range, otherwise specifi cations are at T
A
= 25°C. Test conditions are V
+
= 5V, V
–
= 0V, V
CM
= 0.5V unless otherwise noted.
ELECTRICAL CHARACTERISTICS
C SUFFIX H SUFFIX
SYMBOL PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS
CMRR Common Mode Rejection
Ratio
0 ≤ V
CM
≤ 5V
l
70
68
84 70
66
84 dB
dB
PSRR Power Supply Rejection
Ratio
V
S
= 2.5V to 5.5V
l
94
91
115 94
89
115 dB
dB
V
OUT
Output Voltage, High,
(Referred to V
+
)
No Load
I
SOURCE
= 1mA
I
SOURCE
= 5mA
l
l
l
0.5
39
220
5
85
460
0.5
39
220
10
100
mV
mV
mV
Output Voltage, Low,
(Referred to V
–
)
No Load
I
SINK
= 1mA
I
SINK
= 5mA
l
l
l
0.5
36
200
5
85
460
0.5
36
200
10
100
mV
mV
mV
A
VOL
Large-Signal Voltage Gain R
LOAD
= 10k, 0.5V ≤ V
OUT
≤ 4.5V
l
1000
400
5000 1000
300
5000 V/mV
V/mV
I
SC
Output Short-Circuit
Current
Source and Sink
l
7.7
6
12.5 7.7
4.5
12.5 mA
mA
SR Slew Rate A
V
= 1 0.5 0.5 V/µs
GBW Gain Bandwidth Product
(f
TEST
= 10kHz)
R
LOAD
= 50k, V
CM
= 2.5V
l
0.9
0.7
1.5 0.9
0.6
1.5 MHz
Φ
0
Phase Margin R
L
= 10k, C
L
= 150pF, A
V
= 1 45 45 Deg
t
S
Settling Time 0.1% V
STEP
= 1V, A
V
= 1 5 5 µs
I
S
Supply Current
(Per Amplifi er)
No Load
l
110 130
140
110 130
145
µA
µA
Shutdown Current
(Per Amplifi er)
Shutdown, V
SHDNx
≤ 1.2V
l
1.1 1.8 1.1 2 µA
V
S
Supply Voltage Range Guaranteed by the PSRR Test
l
2.5 5.5 2.5 5.5 V
Channel Separation f
S
= 10kHz –120 –120 dB
Shutdown Logic SHDNx High
SHDNx Low
3.5
1.2
3.5
1.2
V
V
t
ON
Turn On Time V
SHDNx
= 1.2V to 3.5V 7 7 µs
t
OFF
Turn Off Time V
SHDNx
= 3.5V to 1.2V 1 1 µs
Leakage of SHDN Pin V
SHDNx
= 0V
l
0.5 0.9 0.5 1.2 µA
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: A heat sink may be required to keep the junction temperature
below the absolute maximum. This depends on the power supply voltage
and the total output current.
Note 3: The LTC6084C/LTC6085C are guaranteed functional over the
operating temperature range of –40°C to 85°C. The LTC6084H/LTC6085H
are guaranteed functional over the operating temperature range of –40°C
to 125°C.
Note 4: The LTC6084C/LTC6085C are guaranteed to meet specifi ed
performance from 0°C to 70°C. The LTC6084C/LTC6085C are designed,
characterized and expected to meet specifi ed performance from –40°C
to 85°C but are not tested or QA sampled at these temperatures. The
LTC6084H/LTC6085H are guaranteed to meet specifi ed performance from
–40°C to 125°C.
Note 5: ESD (Electrostatic Discharge) sensitive device. ESD protection
devices are used extensively internal to the LTC6084/LTC6085; however,
high electrostatic discharge can damage or degrade the device. Use proper
ESD handling precautions.
Note 6: This parameter is not 100% tested.
Note 7: This specifi cation is limited by high speed automated test
capability. See Typical Performance Characteristic curves for actual
performance.
Note 8: Current noise is calculated from i
n
= √2qI
B
, where q = 1.6 • 10
–19
coulombs.
