4
Charge Injection, Q C
L
= 1.0nF, V
G
= 0V, R
G
= 0Ω, (See Figure 2) 25 - - 5 pC
COM ON Capacitance, C
COM(ON)
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, (See Figure 7) 25 - 34 - pF
OFF Isolation R
L
= 50Ω, C
L
= 15pF, f = 1MHz,
V
NO
or V
NC
= 1V
RMS
, (See Figures 4 and 6)
25 - 71 - dB
Crosstalk, (Note 9) 25 - -89 - dB
POWER SUPPLY CHARACTERISTICS
Power Supply Range Full ±2-±6V
Positive Supply Current, I+ V
S
= ±5.5V, V
IN
= 0V or V+, Switch On or Off 25 -1 0.01 1 µA
Full -1 - 1 µA
Negative Supply Current, I- 25 -1 0.01 1 µA
Full -1 - 1 µA
NOTES:
5. V
IN
= Input voltage to perform proper function.
6. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
7. Leakage parameter is 100% tested at high temp, and guaranteed by correlation at 25
o
C.
8. Flatness is defined as the delta between the maximum and minimum R
ON
values over the specified voltage range. Flatness specifications are
guaranteed only with specified voltages.
9. Between any two switches.
Electrical Specifications: 5V Supply Test Conditions: V+ = +4.5V to +5.5V, V- = GND = 0V, V
INH
= 2.4V, V
INL
= 0.8V (Note 5),
Unless Otherwise Specified
PARAMETER TEST CONDITIONS
TEMP
(
o
C)
MIN
(NOTE 6) TYP
MAX
(NOTE 6)UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
Full 0 - V+ V
ON Resistance, R
ON
V+ = 4.5V, I
COM
= 1.0mA, V
NO
or V
NC
= 3.5V,
(See Figure 5)
25 - 30 60 Ω
Full - - 75 Ω
R
ON
Matching Between Channels,
∆R
ON
V+ = 5V, I
COM
= 1.0mA, V
NO
or V
NC
= 3V 25 - 0.8 2 Ω
Full - - 4 Ω
R
ON
Flatness, R
FLAT(ON)
V+ = 5V, I
COM
= 1.0mA, V
NO
or V
NC
= 1V, 3V, (Note 8) 25 - - 6 Ω
Full - - 8 Ω
NO or NC OFF Leakage Current,
I
NO(OFF)
or I
NC(OFF)
V+ = 5.5V, V
COM
= 1V, 4.5V, V
NO
or V
NC
= 4.5V, 1V,
(Note 7)
25 -0.1 - 0.1 nA
Full -2.5 - 2.5 nA
COM OFF Leakage Current,
I
COM(OFF)
V+ = 5.5V, V
COM
= 1V, 4.5V, V
NO
or V
NC
= 4.5V, 1V,
(Note 7)
25 -0.1 - 0.1 nA
Full -2.5 - 2.5 nA
COM ON Leakage Current,
I
COM(ON)
V+ = 5.5V, V
COM
= 1V, 4.5V, (Note 7) 25 -0.2 - 0.2 nA
Full -5.0 - 5.0 nA
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
V+ = 5V, V
NO
or V
NC
= 3V, R
L
= 300Ω, C
L
= 35pF,
V
IN
= 0 to 3V, (See Figure 1)
25 - 85 170 ns
Full - - 240 ns
Turn-OFF Time, t
OFF
V+ = 5V, V
NO
or V
NC
= 3V, R
L
= 300Ω, C
L
= 35pF,
V
IN
= 0 to 3V, (See Figure 1)
25 - 25 50 ns
Full - - 100 ns
Electrical Specifications: ±5V Supply Test Conditions: V
SUPPLY
= ±4.5V to ±5.5V, GND = 0V, V
INH
= 2.4V, V
INL
= 0.8V (Note 5),
Unless Otherwise Specified (Continued)
PARAMETER TEST CONDITIONS
TEMP
(
o
C)
(NOTE 6)
MIN TYP
(NOTE 6)
MAX UNITS
ISL8391, ISL8392, ISL8393
