EL7457CLZ-T13

1
FN7288.4
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2002-2005, 2012. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
EL7457
40MHz Non-Inverting Quad CMOS Driver
The EL7457 is a high speed, non-inverting, quad CMOS
driver. It is capable of running at clock rates up to 40MHz
and features 2A peak drive capability and a nominal
on-resistance of just 3Ω. The EL7457 is ideal for driving
highly capacitive loads, such as storage and vertical clocks
in CCD applications. It is also well suited to ATE pin driving,
level-shifting, and clock-driving applications.
The EL7457 is capable of running from single or dual power
supplies while using ground referenced inputs. Each output
can be switched to either the high (V
H
) or low (V
L
) supply
pins, depending on the related input pin. The inputs are
compatible with both 3V and 5V CMOS and TTL logic. The
output enable (OE) pin can be used to put the outputs into a
high-impedance state. This is especially useful in CCD
applications, where the driver should be disabled during
power down.
The EL7457 also features very fast rise and fall times which
are matched to within 1ns. The propagation delay is also
matched between rising and falling edges to within 2ns.
The EL7457 is available in 16-pin QSOP, 16-pin SO
(0.150"), and 16-pin QFN packages. All are specified for
operation over the full -40°C to +85°C temperature range.
Pinouts
Features
Clocking speeds up to 40MHz
4 channels
12ns t
R
/t
F
at 1000pF C
LOAD
1ns rise and fall time match
1.5ns prop delay match
Low quiescent current - <1mA
Fast output enable function - 12ns
Wide output voltage range
•8V V
L
-5V
•-2V V
H
16.5V
2A peak drive
•3Ω on resistance
Input level shifters
TTL/CMOS input-compatible
Pb-free (RoHS compliant)
Applications
CCD drivers
Digital cameras
Pin drivers
Clock/line drivers
Ultrasound transducer drivers
Ultrasonic and RF generators
Level shifting
1
2
3
4
16
15
14
13
5
6
7
12
11
10
8 9
1
2
3
4
12
11
10
9
5
6
7
8
16
15
14
13
INB
VL
VL
GND
INC
IND
VS-
OUTD
OE
INA
VS+
OUTA
OUTB
VH
VH
OUTC
THERMAL
PAD*
INA
OE
INB
VL
GND
NC
INC
IND
VS+
OUTA
OUTB
NC
VH
OUTC
OUTD
VS-
EL7457
[16-PIN SO (0.150”),
QSOP (0.150”)]
TOP VIEW
EL7457
[16-PIN QFN (4X4MM)]
TOP VIEW
* THERMAL PAD CONNECTED
TO PIN 7 (V
S
-)
Data Sheet January 26, 2012
2
FN7288.4
January 26, 2012
Ordering Information
PART NUMBER
(Notes 2, 3)
PART
MARKING
TEMP.
RANGE (°C)
PACKAGE
(Pb-free)
PKG.
DWG. #
EL7457CUZ 7457CUZ -40°C to +85°C 16 Ld QSOP (0.150”) MDP0040
EL7457CUZ-T13 (Note 1) 7457CUZ -40°C to +85°C 16 Ld QSOP (0.150”) MDP0040
EL7457CUZ-T7 (Note 1) 7457CUZ -40°C to +85°C 16 Ld QSOP (0.150”) MDP0040
EL7457CUZ-T7A (Note 1) 7457CUZ -40°C to +85°C 16 Ld QSOP (0.150”) MDP0040
EL7457CSZ EL7457CSZ -40°C to +85°C 16 Ld SO (0.150”) MDP0027
EL7457CSZ-T13 (Note 1) EL7457CSZ -40°C to +85°C 16 Ld SO (0.150”) MDP0027
EL7457CSZ-T7 (Note 1) EL7457CSZ -40°C to +85°C 16 Ld SO (0.150”) MDP0027
EL7457CSZ-T7A (Note 1) EL7457CSZ -40°C to +85°C 16 Ld SO (0.150”) MDP0027
EL7457CLZ 7457CLZ -40°C to +85°C 16 Ld QFN (4x4mm) L16.4X4H
EL7457CLZ-T13 (Note 1) 7457CLZ -40°C to +85°C 16 Ld QFN (4x4mm) L16.4X4H
EL7457CLZ-T7 (Note 1) 7457CLZ -40°C to +85°C 16 Ld QFN (4x4mm) L16.4X4H
EL7457CLZ-T7A (Note 1) 7457CLZ -40°C to +85°C 16 Ld QFN (4x4mm) L16.4X4H
NOTES:
1. Please refer to TB347
for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin
plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free
products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), please see device information page for EL7457
. For more information on MSL please see tech brief TB363.
EL7457
3
FN7288.4
January 26, 2012
Absolute Maximum Ratings (T
A
= 25°C) Thermal Information
Supply Voltage (V
S
+ to V
S
-) . . . . . . . . . . . . . . . . . . . . . . . . . . .+18V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . .V
S
- -0.3V, V
S
+ +0.3V
Continuous Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . 100mA
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C
Thermal Resistance θ
JA
(°C/W) θ
JC
(°C/W)
16 Ld QFN (Notes 4, 5) . . . . . . . . . . . . 43 5
16 Ld SOIC (Notes 6, 7). . . . . . . . . . . . 73 45
16 Ld QSOP (Note 6). . . . . . . . . . . . . . 112 N/A
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Maximum Die Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . +125°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
4. θ
JA
is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
Tech Brief TB379
.
5. For θ
JC
, the “case temp” location is the center of the exposed metal pad on the package underside.
6. θ
JA
is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
7. For θ
JC
, the “case temp” location is taken at the package top center.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: T
J
= T
C
= T
A
Electrical Specifications V
S
+ = +5V, V
S
- = -5V, V
H
= +5V, V
L
= -5V, T
A
= 25°C, unless otherwise specified.
PARAMETER DESCRIPTION CONDITION
MIN
(Note 8) TYP
MAX
(Note 8) UNIT
INPUT
V
IH
Logic “1” Input Voltage 2.0 V
I
IH
Logic “1” Input Current V
IH
= 5V 0.1 10 µA
V
IL
Logic “0” Input Voltage 0.8 V
I
IL
Logic “0” Input Current V
IL
= 0V 0.1 10 µA
C
IN
Input Capacitance 3.5 pF
R
IN
Input Resistance 50 MΩ
OUTPUT
R
OH
ON Resistance V
H
to OUTx I
OUT
= -100mA 4.5 6 Ω
R
OL
ON Resistance V
L
to OUTx I
OUT
= +100mA 4 6 Ω
I
LEAK
Output Leakage Current V
H
= V
S
+, V
L
= V
S
-0.110µA
I
PK
Peak Output Current Source 2.0 A
Sink 2.0 A
POWER SUPPLY
I
S
Power Supply Current Inputs = V
S
+0.51.5mA
SWITCHING CHARACTERISTICS
t
R
Rise Time C
L
= 1000pF 13.5 ns
t
F
Fall Time C
L
= 1000pF 13 ns
t
RFΔ
t
R
, t
F
Mismatch C
L
= 1000pF 0.5 ns
t
D
+ Turn-Off Delay Time C
L
= 1000pF 12.5 ns
t
D
- Turn-On Delay Time C
L
= 1000pF 14.5 ns
t
DD
t
D-1
- t
D-2
Mismatch C
L
= 1000pF 2 ns
t
ENABLE
Enable Delay Time 12 ns
EL7457

EL7457CLZ-T13

Mfr. #:
Manufacturer:
Renesas / Intersil
Description:
Gate Drivers EL7457CLZ 40 MHZ NON INVERT QD CMOS DRVR
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union