High current connectors A35P (0.35mm pitch)
–2–
ACCTB81E 201602-T
PRODUCT TYPES
Notes: 1. Order unit:
For volume production: 1-inner carton (1-reel) units
For samples, please contact our sales office.
2. Please contact us for connectors having a number of pins other than those listed above.
SPECIFICATIONS
1. Characteristics
Mated height Number of pins
Part number Packing
Socket Header Inner carton (1-reel) Outer carton
0.8mm
10 AXF5A1012 AXF6A1012
5,000 pieces 10,000 pieces
12 AXF5A1212 AXF6A1212
16 AXF5A1612 AXF6A1612
20 AXF5A2012 AXF6A2012
24 AXF5A2412 AXF6A2412
30 AXF5A3012 AXF6A3012
34 AXF5A3412 AXF6A3412
40 AXF5A4012 AXF6A4012
44 AXF5A4412 AXF6A4412
50 AXF5A5012 AXF6A5012
54 AXF5A5412 AXF6A5412
60 AXF5A6012 AXF6A6012
64 AXF5A6412 AXF6A6412
70 AXF5A7012 AXF6A7012
80 AXF5A8012 AXF6A8012
100 AXF5A0012 AXF6A0012
Item Specifications Conditions
Electrical
characteristics
Rated current
1.5 A/pin contact × 4 pin contacts or
1.25 A/pin contact × 8 pin contacts (as power contact)
0.5 A/pin contact (as signal contact)
(Max. 12 A at total pin contacts)
Rated voltage 30V AC/DC
Dielectric strength 150V AC for 1 min.
No short-circuiting or damage at a detection current of
1 mA when the specified voltage is applied for one minute.
Insulation resistance Min. 1,000MΩ (initial) Using 250V DC megger (applied for 1 min.)
Contact resistance Max. 30mΩ
Based on the contact resistance measurement method
specified by JIS C 5402.
Mechanical
characteristics
Composite insertion force Max. 0.981N/pin contact × pin contacts (initial)
Composite removal force Min. 0.165N/pin contact × pin contacts
Contact holding force
(Socket contact)
Min. 0.20N/pin contact
Measuring the maximum force.
As the contact is axially pull out.
Environmental
characteristics
Ambient temperature –55°C to +85°C No icing or condensation.
Soldering heat resistance
Peak temperature: 260°C or less (on the surface of the
PC board around the connector terminals)
Infrared reflow soldering
300°C within 5 sec. 350°C within 3 sec. Soldering iron
Storage temperature
–55°C to +85°C (product only)
–40°C to +50°C (emboss packing)
No icing or condensation.
Thermal shock resistance
(header and socket mated)
5 cycles,
insulation resistance min. 100MΩ,
contact resistance max. 30mΩ
Conformed to MIL-STD-202F, method 107G
Humidity resistance
(header and socket mated)
120 hours,
insulation resistance min. 100MΩ,
contact resistance max. 30mΩ
Conformed to IEC60068-2-78
Bath temperature 40°C±2°C,
humidity 90% to 95% R.H.
Saltwater spray resistance
(header and socket mated)
24 hours,
insulation resistance min. 100MΩ,
contact resistance max. 30mΩ
Conformed to IEC60068-2-11
Bath temperature 35°C±2°C,
saltwater concentration 5%±1%
H2S resistance
(header and socket mated)
48 hours,
contact resistance max. 30mΩ
Bath temperature 40°C±2°C,
gas concentration 3 ppm ±1 ppm,
humidity 75% to 80% R.H.
Lifetime
characteristics
Insertion and removal life 30 times
Repeated insertion and removal speed of max. 200 times/
hours
Unit weight 60 pin contact Socket 0.03 g Header 0.02 g
Order Temperature (°C) Time (minutes)
1
2
3
4
–55
85
–55
0
−3
30
Max. 5
30
Max. 5
+3
0
0
−3