OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

02560994-000

P1-P3P4-P4
SENSOR SOLUTIONS ///DC-SE Series 07/2017
Page 1
FEATURES
Unipolar DC operation
Low power consumption
Shock and vibration tolerant
Captive core option (available on
select models)
AISI 400 Series stainless steel
housing
CE compliant
Calibration certificate supplied
with each unit
APPLICATIONS
Factory floor automation
Position feedback
Data collection
Process control
Metrology
Portable / battery powered
measurements
General industrial
DC-SE SERIES
General purpose DC LVDT
SPECIFICATIONS
Single-Ended DC operation
Low 6mA current consumption
Stroke ranges from 0.1 to 6 inches
0.25% linearity
Stainless steel housing
Double magnetic shielding
EMI/ESD protected
1 meter long shielded cable
Captive core option
The DC-SE Series LVDTs operate on a single-ended DC power supply,
and provide either a 0 to +5VDC or +1 to +6VDC output signal (wiring
dependent) over their full range of displacement. The extremely linear
and low noise output makes the DS-SE Series the perfect choice for
interfacing to unipolar inputs of analog-to-digital converters, PLC’s, and
various data collection systems.
The DC-SE is internally regulated, thus providing immunity to line ripple
and allowing operation from unregulated power sources of between 8.5
and 28VDC. The very low typical 6mA current draw is ideal for remote
or battery powered applications. The highly stable oscillator provides
excellent temperature performance throughout the operating
temperature range, while synchronous demodulation insures superb
noise rejection.
The built-in EMI/ESD protection and the shielded cable permit operation
in noisy industrial environments, with double magnetic shielding
providing the utmost protection from stray fields.
Like in most of our LVDTs, the DC-SE windings are vacuum
impregnated with a specially formulated, high temperature, flexible
resin, and the coil assembly is potted inside its housing with a two-
component epoxy. This provides excellent protection against hostile
environments such as high humidity, vibration and shock.
Available in a variety of stroke ranges from 0.1 to 6 inches, the DC-EC
Series can be configured with a number of standard options including
metric threaded core, guided core and small diameter/low mass core.
Captive core option: The DC-EC features an optional captive core
design (available for most models) that greatly simplifies installation.
The core rod and bearing assembly includes a Bronze bearing on the
front end for self-alignment, while a PTFE sleeve allows low-friction
travel through the stainless steel boreliner (spool tube). The core rod
and the bearing assembly are both field serviceable.
DC-SE SERIES
General purpose DC LVDT
SENSOR SOLUTIONS /// DC-SE Series 07/2017
Page 2
PERFORMANCE SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
DC-SE 100
DC-SE 250
DC-SE 500
DC-SE 1000
DC-SE 2000
DC-SE 4000
DC-SE 6000
0.10 [2.54]
0.25 [6.35]
0.50 [12.7]
1.0 [25.4]
2.0 [50.8]
4.0 [101.6]
6.0 [152.4]
50
20
10
5
2.5
1.25
0.833
1.97
0.787
0.394
0.197
0.098
0.0492
0.0328
+8.5 to +28VDC
1mV/VDC, maximum; 0.2mV/VDC, typical
10mA maximum; 6mA typical
0 to +5VDC (4 wire), +1 to +6VDC (3 wire) - Increases when the core is displaced towards the cable
5mA maximum
±0.25% of FR, maximum
10 mVRMS, maximum
0.125% of FSO
0.028%/ºF [0.05%/C], maximum
Frequency response
200 Hertz @ -3dB
ENVIRONMENTAL SPECIFICATIONS & MATERIALS
-13°F to +185°F [-25°C to 85°C] Operating; -65°F to +257°F [-55°C to 125°C] Survival
250 g (11ms half-sine)
10 g up to 2kHz
AISI 400 Series stainless steel
Cable with 4 conductor, 28AWG, stranded copper, braided shield and polyurethane jacket,
39 inches [1 meter] long. Shield is connected to case.
IP61
Notes:
All values are nominal unless otherwise noted; Dimensions are in inch [mm] unless otherwise noted
FR: Full Range is the stroke range, end to end; FR=S for 0 to S stroke range
FSO (Full Scale Output): Largest absolute value of the outputs measured at the ends of the range
WIRING SCHEMATIC & BLOCK DIAGRAM
3-wire hookup for +1 to +6VDC output 4-wire hookup for 0 to +5VDC output
Important: NEVER connect SIG COM and PWR COM together; NEVER connect SIG COM to other DC-SE’s
DC-SE SERIES
General purpose DC LVDT
SENSOR SOLUTIONS /// DC-SE Series 07/2017
Page 3
MECHANICAL SPECIFICATIONS – NON-CAPTIVE CORE (STANDARD)
Parameter
DC-SE 100
DC-SE 250
DC-SE 500
DC-SE 1000
DC-SE 2000
DC-SE 4000
DC-SE 6000
Main body length
“A”
3.51
[89.2]
4.36
[110.7]
5.20
[132.1]
6.89
[175.0]
8.87
[225.3]
12.25
[311.2]
17.3
[439.4]
Core length
“B”
0.585
[14.9]
1.10
[27.9]
1.80
[45.7]
3.00
[76.2]
3.80
[96.5]
5.30
[134.6]
6.20
[157.5]
Length of bore
“C”
1.21
[30.7]
2.06
[52.2]
2.91
[73.8]
4.59
[116.7]
6.57
[166.8]
9.95
[252.8]
15.06
[382.5]
Center of core
position at null “P”
0.51
[13.0]
0.93
[23.6]
1.35
[34.3]
2.20
[55.9]
3.19
[81.0]
4.88
[124.0]
7.56
[192.0]
Body weight oz
[gram]
2.54
[72]
3.21
[91]
3.39
[96]
4.38
[124]
6.25
[177]
8.33
[236]
10.48
[297]
Core weight oz
[gram]
0.035
[1]
0.11
[3]
0.18
[5]
0.28
[8]
0.35
[10]
0.53
[15]
0.64
[18]
Dimensions are in inch [mm]
MECHANICAL SPECIFICATIONS – CAPTIVE CORE OPTION
Parameter
DC-SE 100
DC-SE 250
DC-SE 500
DC-SE 1000
DC-SE 2000
DC-SE 4000
DC-SE 6000
Main body length
“A”
3.85
[97.8]
4.70
[119.4]
5.54
[140.7]
7.23
[183.6]
9.21
[233.9]
12.59
[319.8]
17.64
[448.1]
Core rod position
at null “R”
3.69
[93.7]
4.28
[108.7]
4.75
[120.6]
6.04
[153.4]
7.90
[200.7]
10.52
[267.2]
15.27
[387.9]
Center of core
position at null “P”
0.85
[21.6]
1.27
[32.2]
1.69
[42.9]
2.54
[64.5]
3.53
[89.7]
5.22
[132.6]
7.90
[200.7]
Weight, oz [gram]
1.52 [43]
4.09 [116]
4.34 [123]
5.51 [156]
7.62 [216]
10.13 [287]
12.92 [366]
Dimensions are in inch [mm]
P1-P3P4-P4

02560994-000

Mfr. #:
Buy 02560994-000
Manufacturer:
TE Connectivity
Description:
Linear Displacement Sensors 2in Gen Pur LVDT DC S End 0.25% Lin
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet