DO NOT
SCALE FROM
THIS PRINT
LTH-XXX-XX-X-D-A-XX
No OF POSITIONS
-010, -020, -030, -040, -050,
(PER ROW)
LEAD STYLE
-01:SURFACE MOUNT
(USE SUB-T-1M18-01-X PIN)
PLATING SPECIFICATION
-G: 10µ" GOLD IN CONTACT AREA,
3µ" GOLD ON TAIL
-H: 30µ" HEAVY GOLD IN CONTACT
AREA, 3µ" GOLD ON TAIL
OPTION
-TR: TAPE AND REEL
-K: POLYAMIDE FILM PAD
(USE K-500-300, SEE FIG. 2)
ROW SPECIFICATION
-D: DOUBLE
(USE LTH-XXX-01-D-A)
-A: ALIGNMENT PIN
.061
REF
1.55
.035
REF
0.89
"A"
"A"
LTH-XXX-01-D-A
.189 4.80
REF
.140 3.56
REF
((No OF POS + 2) x .01969[.5000]) + .1100[2.794] REF
.039
REF
0.99
.008 0.20
.030
REF
0.76
.050 1.27
REF
.085 2.16
REF
.065
REF
1.66
((No OF POS+1)x.01969[.5000]
.002[.05]
(((No OF POS/2) - 1)
x .01969) REF
01
02
SEE NOTE 10
SEE NOTE 10
C
((No OF POS+2)x.01969[.5000])+.050[1.270]
REF
.030
REF
0.76
.030
REF
0.76
.020
±.003
0.50
±0.08
(MEASURE AT TIPS)
C
C
L
.066
±.003
1.68
±0.08
.030
REF
0.77
.016 0.41
REF
.199
±.008
5.05
±0.20
(SEE NOTE 7)
.030
REF
0.77
.1390
±.0020
3.531
±0.05
'A'
SECTION "A"-"A"
SCALE 10 : 1
SUB-T-1M18-01-X
SEE NOTE 6
C
C
C
.004[.10]
SHEAR TO .004[.10]
MAX BURR
DETAIL 'A'
SCALE 20 : 1
C
C
FIG 1
LTH-020-01-X-D-A SHOWN
SHEET OF
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS ANGLES
.XX:
.01[.3] 2
.XXX:
.005[.13]
.XXXX:
.0020[.051]
MATERIAL:
BY:
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
7/1/99
2
1
SHEET SCALE: 5:1
INSULATOR: BLACK LCP
CONTACT: PHOS. BRONZE
F:\DWG\MISC\MKTG\LTH-XXX-XX-X-D-A-XX-MKT.SLDDRW
NOTES:
1. REPRESENTS A CRITICAL DIMENSION.
2. BURR ALLOWANCE: .001[.03] MAX.
3. MINIMUM PUSHOUT FORCE: 6 OZ MIN.
4. PARTS TO BE MOLDED TO POSITION
5. NOTE DELETED.
6. CUT IN THIS AREA MUST BE BELOW SURFACE MOUNT
LEADS.
7. MAX VARIATION BETWEEN ADJACENT PINS TO BE
.002[0.05] MAX.
8.
NOTE DELETED.
9.
NOTE DELETED.
10. VOIDS CAN BE USED AT VENDORS DISCRETION
TO CONTROL WARP.
.5mm LOW PROFILE TERMINAL ASSEMBLY
LTH-XXX-XX-X-D-A-XX
ERIC M
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
REVISION S
