LT3754
4
3754fc
elecTrical characTerisTics
PARAMETER CONDITIONS MIN TYP MAX UNITS
Voltage Gain (LED) 45 V/V
V
C
Source Current (Out of Pin) V
C
= 1.5V, V
LEDx
= 0.8V, OVP
SET
= 1.5V 10 µA
V
C
Sink Current (OVP) V
C
= 1.5V, V
LEDx
= 0.8V, OVP
SET
= 0V 15 µA
V
C
Sink Current (LED) V
C
= 1.5V, V
LEDx
= 1.2V, OVP
SET
= 1.5V 9 µA
V
C
Output High (clamp) (V
COH
) 2.3 V
V
C
Output Low (clamp) (V
COL
) 0.8 V
V
C
Switching Threshold (V
CSW
) 1.1 V
SENSE AMP
SENSE Input Current (Out of Pin) SENSE = 0V 65 µA
SENSE Current Limit Threshold
l
46 52 60 mV
Current Mode Gain ∆V(V
C
)/∆V(SENSE) 6 V/V
SENSE Over Current Limit Threshold
l
90 100 110 mV
LED CURRENT / CONTROL
I
SET
Pin Voltage CTRL = 1.5V 1.00 V
LEDx Current (20mA) (R
ISET
= 14.7k) V
LEDx
= 1V, CTRL = 1.5V 19.29 20.2 21.11 mA
LEDx Current Matching (20mA) (R
ISET
= 14.7k) V
LEDx
= 1V, CTRL = 1.5V
l
±0.7 ±2.8 %
LEDx Current (50mA) (R
ISET
= 5.76k) V
LEDx
= 1V, CTRL = 1.5V 47.85 50.1 52.35 mA
LED Pin Regulation Voltage 1.1 V
T
SET
Threshold 630 mV
ANALOG DIMMING
CTRL Input Current (Out of Pin) CTRL = 1V
CTRL = 0.04V
40
50
200
200
nA
nA
LEDx Current (Dimming 25:1) V
LEDx
= 1V, CTRL = 0.04V 0.8 mA
PWM DIMMING
PWM Input Low Threshold 0.7 1 V
PWM Input High Threshold 1.1 1.4 V
PWM Input Current PWM = 1.5V
PWM = 6V
6
24
µA
µA
V
OUT
Pin Current in PWM Mode V(V
OUT
) = 60V PWM = 1.5V
PWM = 0V
370
20
µA
µA
LEDx Leakage Current
(PWM = 0V)
V
LEDx
= 1V, V
OUT
= 12V
V
LEDx
= 50V, V
OUT
= 60V
0.1
0.1
1
2
µA
µA
FAULT DIAGNOSTICS
FAULT Output Sink Current LED1 = Open, V
FAULT
= 0.3V 0.3 0.6 mA
LED
x
Short Threshold (V
SH
)
(V
OUT
– V
LEDx
)
V
OUT
= 12V
V
OUT
= 60V
6
6
V
V
LED Open Detection Threshold V
OUT
= 12V 0.5 V
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. V
IN
= V
OUT
= 6V, R
ISET
= 14.7k unless otherwise noted.
LT3754
5
3754fc
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LT3754E is guaranteed to meet performance specifications
from 0°C to 125°C junction temperature. Specifications over the –40°C
to 125°C operating junction temperature range are assured by design,
characterization and correlation with statistical process controls. The
elecTrical characTerisTics
PARAMETER CONDITIONS MIN TYP MAX UNITS
GATE DRIVER
GATE Driver Output Rise Time V
IN
= 7V, C
L
= 3300pF (Note 4) 30 nS
GATE Driver Output Fall Time V
IN
= 7V, C
L
= 3300pF (Note 4) 30 nS
GATE Output Low I
GATE
= 0µA 0.1 V
GATE Output High INTV
CC
= V
IN
= 7V
I
GATE
= 0µA
6.95
V
OUTPUT VOLTAGE
V
OUT
Over Voltage Protection (OVP) Regulation Voltage OVP
SET
= 0.22V
OVP
SET
= 1V
12.5
57
V
V
OVP
SET
Input Current (Out of Pin) OVP
SET
= 0.22V, V
OUT
=12V 40 200 nA
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. V
IN
= V
OUT
= 6V, R
ISET
=14.7k unless otherwise noted.
Typical perForMance characTerisTics
LED Current
vs Junction Temperature
LED Current
vs CTRL Pin Voltage
LT3754I is guaranteed to meet performance specifications from
40°C to 125°C junction temperature.
Note 3: For Maximum Operating Ambient Temperature, see
Thermal Calculations in the Applications Information section.
Note 4: GATE rise and fall times are measured between 10% and 90%
of INTV
CC
voltage.
Note 5: See Duty Cycle Considerations in the Applications Information.
T
A
= 25°C, unless otherwise noted.
JUNCTION TEMERATURE (°C)
50 25
LED CURRENT MATCHING (%)
0.8
0.4
0.0
0.4
0.8
1000 25
3754 G01
12550 75
R
ISET
= 14.7k (I(LED) = 20mA)
Worst-Case Channels LED
Current Matching
(Normalized to 16-channel Average)
JUNCTION TEMERATURE (°C)
–50
LED CURRENT (mA)
21.00
20.00
20.50
19.50
19.00
7525
3754 G02
125500 100–25
R
ISET
= 14.7k
CTRL (V)
0.00
LED CURRENT (mA)
55
10
5
50
40
30
20
45
35
25
15
0
0.75 1.251.00
3754 G03
1.500.500.25
R
ISET
=
5.76k
7.32k
9.76k
14.7k
29.4k
LT3754
6
3754fc
Typical perForMance characTerisTics
SHDN/UVLO Pin (Hysteresis)
Current vs Junction Temperature
V
IN
Shutdown Current
vs Junction Temperature V
IN
Quiescent Current vs V
IN
V
IN
Quiescent Current
vs Junction Temperature
Switching Frequency
vs Junction Temperature
V
C
High Clamp, Active
and Low Clamp Levels
vs Junction Temperature
LED Current Waveforms
3000:1 PWM Dimming (100Hz)
V
REF
vs Junction Temperature
SHDN/UVLO Threshold
vs Junction Temperature
T
A
= 25°C, unless otherwise noted.
5µs/DIV
I(LEDx)
20mA/DIV
PWM
10V/DIV
I(L)
1A/DIV
3754 G04
JUNCTION TEMPERATURE (°C)
–50
V
REF
VOLTAGE (V)
1.525
1.485
1.465
1.505
1.445
25 100750 50
3754 G05
125–25
JUNCTION TEMERATURE (°C)
–50
SHDN/UVLO PIN VOLTAGE (V)
1.525
1.485
1.465
1.505
1.445
25 100750 50
3754 G06
125–25
JUNCTION TEMPERATURE (°C)
–50
SHDN/UVLO PIN CURRENT (µA)
2.80
2.60
2.50
2.40
2.30
2.70
2.20
25 100750 50
3754 G07
125–25
JUNCTION TEMPERATURE (°C)
–50
V
IN
CURRENT (µA)
5
3
2
1
4
0
25 100750 50
3754 G08
125–25
V
IN
= 6V, SHDN/UVLO = 0V
V
IN
(V)
0
V
IN
CURRENT (mA)
12
6
4
2
8
10
0
15 30 352510 20
3754 G09
405
PWM = 1.5V, NO SWITCHING,
V(LED
1-16
) = 1.2V, CTRL = 0.1V
PWM = 0V, CTRL = 0.1V
R
ISET
= 14.7k
JUNCTION TEMPERATURE (°C)
–50
V
IN
CURRENT (mA)
15
5
10
0
25 100750 50
3754 G10
125–25
V
IN
= 6V, R
ISET
= 14.7k, CTRL = 0.1V
PWM = 1.5V, NO SWITCHING,
V(LED
1-16
) = 1.2V, CTRL = 0.1V
PWM = 0V, CTRL = 0.1V
JUNCTION TEMPERATURE (°C)
–50
SWITCHING FREQUENCY (kHz)
1100
950
1050
1000
900
25 100750 50
3754 G11
125–25
RT = 39.2k
JUNCTION TEMPERATURE (°C)
–50
V
C
PIN VOLTAGE (V)
2.5
2.0
1.5
1.0
0.5
0.0
25 100750 50
3754 G12
125–25
V
C
HIGH CLAMP
V
C
LOW CLAMP
V
C
ACTIVE (SWITCHING)

LT3754IUH#PBF

Mfr. #:
Manufacturer:
Analog Devices / Linear Technology
Description:
LED Lighting Drivers 16-Ch 50mA LED Drvr
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union