NIPPON CHEMI-CON CORPORATION
1435
1
Engineering Bulletin
Conductive Polymer
Aluminum Solid Capacitors
No.795 / Apr.2008
Specifi cations in this bulletin are subject to change without notice.
@Super low ESR, high ripple current capability
@Downsized from PSC series (F8B8L to F6.3B8L)
@Endurance is longer life than PSC series (5,000 hours at 105C)
@ESR after endurance is specifi ed within the initial spec
@Rated voltage range : 2.5 to 6.3V
dc
@RoHS Compliant
@Halogen Free
?
SPECIFICATIONS
(at 20C, 120Hz)
(at 105C)
(at 20C after 2 minutes)
(at 20C, 120Hz)
(at 100kHz)
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
*Note
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max.Impedance Ratio)
Endurance
Bias Humidity Test
Surge Voltage Test
Halogen Free
(Definition)
Failure Rate
Items
-
55 to +105C
2.5 to 6.3Vdc
P20% (M)
Rated voltage(V)B1.15
I=0.2CV or 500MA, whichever is greater
Where, I : Leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V)
0.10 max.
Z(
-
25C)/Z(+20C)[1.15
Z(
-
55C)/Z(+20C)[1.25
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 5,000 hours
at 105C.
Appearance No significant damage
Capacitance change [P20% of the initial value
D.F. (tanE) [The initial specified value
ESR [The initial specified value
Leakage current [The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to DC voltage at 60C,
90 to 95% RH for 1,000 hours.
Appearance No significant damage
Capacitance change [P20% of the initial value
D.F. (tanE) [The initial specified value
ESR [The initial specified value
Leakage current [The initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds
through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds.
Appearance No significant damage
Capacitance change [P20% of the initial value
D.F. (tanE) [The initial specified value
ESR [The initial specified value
Leakage current [The initial specified value
All homogeneous materials within a capacitor meet the criteria in Table-1 and Tabel-2.
Homogeneous material has uniform composition throughout and cannot be mechanically disjointed into different materials.
Table-1
Substance
Bromine (Br)
Chlorine (Cl)
Total concentration of
Chlorine (Cl) + Bromine (Br)
0.5% per 1,000 hours maximum (Confidence level 60% at 105C)
Characteristics
Permissible limit (by weight)
[900ppm (0.09%)
[900ppm (0.09%)
[1,500ppm (0.15%)
Permissible limit (by weight)
[1,000ppm (0.10%)
[1,000ppm (0.10%)
Table-2
Substance
Antimony Trioxide (Sb
2
O
3
)
Red Phosphorus
?
DIMENSIONS [mm]
?
MARKING
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105
C
.
Size code
fD
fd
F
fD'
L'
F08
6.3
0.6
2.5
FD+0.5max.
L+1.5max.
Coated Case
L'
15min. 4min.
FD'
Fd
FP0.5
E
6D6
820
2.5
V
EX) 2.5V820MF
@Terminal Code : E
Halogen Free
Downsized
Long Life