FDZ204P Rev. D4 (W)
Electrical Characteristics T
A
= 25°C unless otherwise noted
Symbol Parameter Test Conditions Min Typ Max Units
Off Characteristics
BV
DSS
Drain–Source Breakdown Voltage
V
GS
= 0 V, I
D
= –250 µA
–20 V
∆BVDSS
∆T
J
Breakdown Voltage Temperature
Coefficient
I
D
= –250 µA, Referenced to 25°C
–17
mV/°C
I
DSS
Zero Gate Voltage Drain Current V
DS
= –16 V, V
GS
= 0 V –1
µA
I
GSSF
Gate–Body Leakage, Forward V
GS
= –12 V, V
DS
= 0 V –100 nA
I
GSSR
Gate–Body Leakage, Reverse V
GS
= 12 V, V
DS
= 0 V 100 nA
On Characteristics (Note 2)
V
GS(th)
Gate Threshold Voltage
V
DS
= V
GS
, I
D
= –250 µA
–0.6 –0.9 –1.5 V
∆VGS(th)
∆T
J
Gate Threshold Voltage
Temperature Coefficient
I
D
= –250 µA, Referenced to 25°C
3
mV/°C
R
DS(on)
Static Drain–Source
On–Resistance
V
GS
= –4.5 V, I
D
= –4.5 A
V
GS
= –2.5 V, I
D
= –3.5 A
V
GS
= –4.5 V, I
D
= –4.5A,T
J
=125°C
37
57
50
45
75
65
mΩ
g
FS
Forward Transconductance V
DS
= –5 V, I
D
= –4.5 A 15 S
Dynamic Characteristics
C
iss
Input Capacitance 884 pF
C
oss
Output Capacitance 258 pF
C
rss
Reverse Transfer Capacitance
V
DS
= –10 V, V
GS
= 0 V,
f = 1.0 MHz
103 pF
Switching Characteristics (Note 2)
t
d(on)
Turn–On Delay Time 12 22 ns
t
r
Turn–On Rise Time 9 18 ns
t
d(off)
Turn–Off Delay Time 36 58 ns
t
f
Turn–Off Fall Time
V
DD
= –6 V, I
D
= –1 A,
V
GS
= –4.5 V, R
GEN
= 6 Ω
24 38 ns
Q
g
Total Gate Charge 9 13 nC
Q
gs
Gate–Source Charge 2 nC
Q
gd
Gate–Drain Charge
V
DS
= –10 V, I
D
= –4.5 A,
V
GS
= –4.5 V
3 nC
Drain–Source Diode Characteristics and Maximum Ratings
I
S
Maximum Continuous Drain–Source Diode Forward Current –1.5 A
V
SD
Drain–Source Diode Forward
Voltage
V
GS
= 0 V, I
S
= –1.5 A (Note 2) –0.76 –1.2 V
t
rr
Diode Reverse Recovery Time 25 nS
Q
rr
Diode Reverse Recovery Charge
I
F
= –5.5 A,
d
iF
/d
t
= 100 A/µs
26 nC
Notes:
1. R
θJA
is determined with the device mounted on a 1 in² 2 oz. copper pad on a 1.5 x 1.5 in. board of FR-4 material. The thermal resistance from the junction to
the circuit board side of the solder ball, R
θJB
, is defined for reference. For R
θJC
, the thermal reference point for the case is defined as the top surface of the
copper chip carrier. R
θJC
and R
θJB
are guaranteed by design while R
θJA
is determined by the user's board design.
a) 67 °C/W when
mounted on a 1in
2
pad
of 2 oz copper, 1.5” x
1.5” x 0.062” thick
PCB
b) 155 °C/W when mounted
on a minimum pad of 2 oz
copper
Scale 1 : 1 on letter size paper
2. 2. Pulse Test: Pulse Width < 300µs, Duty Cycle < 2.0%
FDZ204P