Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice.
Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer.
1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER,
AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: "901/902..." MAY BE REPLACED BY "Axxx".) OTHER CODES AND
SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER.
Page 1 of 1
Raychem, TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks.
Raychem Wire & Cable
501 Oakside Avenue
Redwood City, CA 94063-3800
Phone: 1-800-227-8816
Fax: 1-650-361-6297
DIMENSIONS ARE IN INCHES AND, UNLESS OTHERWISE DESIGNATED, ARE NOMINAL
THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.
REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID.
© 2011-2016 Tyco Electronics Corporation. All rights reserved.
SPECIFICATION CONTROL DRAWING
SCD
55/1822
Title
TWO CONDUCTOR CABLE, SHIELDED, JACKETED,
OUTER SPACE, 600 VOLT
Date
7-21-16
Revision
C
This specification sheet forms a part of the latest issue of Raychem Specification 55/.
COMPONENT WIRES - 55/0812 SHIELD - SILVER-COATED COPPER JACKET - LOW OUTGASSING,
RADIATION-CROSSLINKED,
MODIFIED ETFE
CABLE CONSTRUCTION DETAILS
PART NUMBER
1/
CONDUCTOR
SIZE
(AWG)
SHIELD
SIZE
(AWG)
JACKET THICKNESS
(inch)
OUTSIDE DIAMETER
(inch)
MAXIMUM
WEIGHT
(lbs/1000 ft.)
MINIMUM NOMINAL NOMINAL MAXIMUM
55/1822-28-* 28 38 .006 .008 .103 .108 7.9
55/1822-26-* 26 38 .006 .008 .113 .119 9.6
55/1822-24-* 24 38 .006 .008 .123 .129 11.4
55/1822-22-* 22 38 .006 .008 .133 .140 13.9
55/1822-20-* 20 38 .006 .008 .149 .156 18.0
55/1822-18-* 18 38 .006 .008 .173 .182 24.6
55/1822-26-* 16 38 .006 .008 .187 .196 29.2
55/1822-14-* 14 38 .007 .009 .223 .234 41.8
55/1822-12-* 12 38 .007 .009 .257 .270 57.8
55/1822-10-* 10 38 .007 .009 .303 .318 85.1
55/1822-8-* 8 36 .009 .011 .433 .455 160.
CABLE RATINGS AND ADDITIONAL REQUIREMENTS
TEMPERATURE RATING: 200°C
Maximum continuous conductor temperature
VOLTAGE RATING: 600 volts (rms) at sea level
CROSSLINKED VERIFICATION: 300 ± 3°C for 1 hour
DIELECTRIC WITHSTAND: 1500 volts (rms), 60 Hz
JACKET COLOR: White preferred
JACKET ELONGATION: 50% (minimum)
JACKET FLAWS:
Spark Test, 1000 volts (rms)
Impulse Dielectric Test, 6.0 kV (peak)
RADIATION RESISTANCE: 500 megarads
SHIELD COVERAGE: 85% (minimum)
VACUUM STABILTY:
Total Mass Loss (TML), 1.00% (maximum)
Volatile Condensable Material (VCM), 0.10% (maximum)
VOLTAGE WITHSTAND (Post Environmental):
1500 volts (rms), 60 Hz, 1 minute
1/ PART NUMBER:
The "*" in the part numbers above shall be replaced by
color code designators with a slash separating the
component wire colors and a dash separating the
component wire colors from the jacket color.
Example: AWG 24, blue and white component wires;
white jacket: 55/1822-24-6/9-9
NOTE: Nominal values are for information only. Nominal values are not requirements.
