D
C
B
A
C
B
1
3
45
678
12
34
56
78
2
THE INFORMATION CONTAINED IN THIS DRAWING IS CONFIDENTIAL AND MAY NOT BE
DISCLOSED WITHOUT WRITTEN CONSENT FROM SOURIAU USA, INC.
THIS DRAWING IS A CONTROLLED DOCUMENT FOR SOURIAU USA, INC.
IT IS SUBJECT TO CHANGE WITHOUT NOTIFICATION.
CONTACT THE DOCUMENT CONTROL CENTER FOR THE LATEST REVISION.
DWG. NO.
2x .615#.015
15.62#.38[ ]
TABLE 1-1
COVER SCREW
RBDSC-1P15 - X
K REVISED PER ECN 12046
RSK
08-22-13
SDH
08-22-13
J REVISED PER ECN10531
RKO
04.28.08
SDH
04.28.08
I REVISED PER ECN10405
LY
01.23.08
SDH
01.23.08
H REVISED PER ECN10307
SDH
10.12.07
SDH
10.12.07
G REVISED PER ECN8399
SDH
07.27.04
SDH
07.27.04
F REVISED PER ECN4792
JRD
09.17.01
SDH
09.17.01
5
ADDED CAT NO.RBDSC-2P12 TO THE NOTE
IN FIELD OF DRAWING. (ECN 3234)
RPS
03.06.95
CWL
03.06.95
4
CHANGED SCREW THREAD FROM 6-32
UNC-2A TO 6-32 UNC-3A. (ECN 3061)
CWL
08.04.94
CCP
08.04.94
3
REPOSITIONED INK STAMP ON UNDERSIDE
OF COVER PLATE. ECN 15008
CCP
03.11.94
CCP
03.11.94
2
SEE REV REF PRINT. (ECN 15005)
CCP
03.02.94
CCP
03.02.94
1
SEE REV REF PRINT. (ECN 2378)
DLB
10.28.93
VCE
10.28.93
REV DESCRIPTION
BY
DATE
CHKD
DATE
ANGLES #1$
#.010 [#0.25]THREE PLACES
#.02 [#0.5]TWO PLACES
#.1 [#3]ONE PLACE
INCH [mm]
No. OF PLACES
TOLERANCES
UNLESS OTHERWISE SPECIFIED
THIRD ANGLE PROJECTION
LINEAR
MEASURE:
SE95607
1 OF 1
www.souriau.com
INTERPRET THIS DRAWING IN ACCORDANCE
WITH ASME Y14.5M - 1994.
K
SE95607
REVDRAWING NO.
CUSTOMER
DRAWING SCALE: 5:1
09.14.93
QC : SJ
APPROVAL
09.14.93
MFG : NV
09.14.93
DSGN : SDH
01.21.08
CHKD : SDH
SIZE: D
CAGE NO: 09922
01.21.08
DRAWN: LY
RBDSC-1P15_(SEE TABLE 1-1)
CAT NO.
SECURITY COVER - PROGRAM SWITCH MODULE
DRAWING TITLE
NOTES: UNLESS OTHERWISE SPECIFIED
PROGRAM SWITCH MODULE WITH SEALING PLUGS PURCHASED SEPARATELY
SEE DRAWING BRSD95231 FOR DETAILS.
SWITCH MOUNTING STUD PURCHASED SEPARATELY.SEE DRAWING SC95769
FOR DETAILS
3. SECURITY COVER ASSEMBLIES ARE PACKAGED ONE ASSEMBLY PER BAG.
FEATURES:
1. THE COVER PLATE APPLIES DOWNWARD PRESSURE ON THE SEALING PLUGS.
HOLDING THEM IN THE SEALED POSITION.
2. THE SECURITY COVER SYSTEM DOES NOT INCREASE THE OVERALL LENGTH, HEIGHT
OR WIDTH, OF THE PROGRAM SWITCH MODULE.
3. ALL COMPONENTS ARE SECURED WHILE SETTING SWITCHES. NO DROPPED
OR MISPLACED PARTS.
PLATE SCREWS, AND RETAINING RINGS ASSEMBLED
RBDSC-1P15A SHOWN
A- WITH LOCK WASHERS
(BACC50AL1A)
BASIC COVER WITH SCREWS
(BACC50AL1)
TO INSTALL SECURITY COVER PLATE:
1. FASTEN PROGRAM SWITCH MODULE IN PLACE USING (2) SECURITY COVER/MODULE
MOUNTING STUDS AND (2) ELASTIC LOCK NUTS (PURCHASED SEPARATELY)
2 . THREAD SCREWS INTO UPPER END OF MOUNTING STUDS, TURN EQUALLY
TO MAINTAIN SECURITY COVER PLATE LEVEL WITH SEALING PLUGS.
3. TIGHTEN SCREWS EQUALLY TO BUTT COVER PLATE ON
SEALING PLUGS. CONTINUE TO TIGHTEN UNTIL COVER PLATE
BOTTOMS FIRMLY ON UPPER END OF MOUNTING STUD.
TO ACCESS DIP SWITCHES:
1. LOOSEN ONE SCREW COUNTERCLOCKWISE 2 TURNS. REMOVE THE OTHER
SCREW.
2. SWING THE SECURITY COVER PLATE TO UNCOVER THE SEALING
PLUGS. PULL PLUGS TO ACCESS SWITCHES.
BOEING PART NO., SOURIAU CATALOGE NO., CAGE NO., DATE CODE,
AND PART NAME, INK STAMPED COLOR BLACK AS ILLUSTRATED.
SEE TABLE 1-1
SEALING PLUGS
(NOT INCLUDED)
SECURITY COVER INSTALLED ON PROGRAM SWITCH MODULE
SCALE : NONE
SWITCH COMPARTMENT SECURITY COVER PLATE
RBDSC-1P15A SHOWN ( .024 [0.61]
THICK STAINLESS STEEL) WITH
MOUNTING SCREWS.
NO. 6-32UNC-3A THREAD
STAINLESS STEEL SCREWS
2X STAINLESS STEEL RETAINING RING
RBDSC-1 PROGRAM SWITCH MODULE
(NOT INCLUDED)
RBDSC-1P12 OR RBDSC-2P12
SECURITY COVER/MODULE MOUNTING STUD
(NOT INCLUDED)
